FEP314BL0 Roper Range - Instructions

On my model I removed the oven door. It makes the job a lot easier. Removed two element screws, removed wires off unit. Installed wires on new unit, replaced screws replaced door and tested oven.

I removed the door and racks to get easy access to the electrical connection. I loosened the screws holding the element in place and disconnected the element from the electrical connection. I connected the new element and inserted the screws firmly attaching it in place. I placed the racks in the desired location and then put the door back on the hinges.

1. Turn off the circuit breaker for the oven. 2. Verify that the power is OFF and all baking controls are OFF. 3. Remove all racks from the oven. 4. Remove the 2 screws with a #2 crosshead screwdriver. 5. Gently pull the element out. 6. Pull the spade lug terminals carefully off the element and take the old element out. 7. Put in the new element by attaching the spade lug terminals. 8. Line up the holes and reattach the element to the oven wall with the 2 screws. 9. Verify that all baking controls are off. 10. Turn on the circuit breaker for the oven. 11. Turn on the oven controls and verify that the new element is working. 12. Turn OFF the baking controls and reinstall the racks.

Turn off power,take out 2 screws to release element, unplug wires, pull out old element, put new element in hook up wires, put in 2 screws, and walla all done. Turn power back on. One thing to do that I did not. Clean the tag off before starting element. I got smoke from that.

Removed screws holding element in place. Removed wire leads from element. Wire leads were under a bit of tension which pulled them back through their holes in rear oven wall. This required taking back of oven off to reinsert wires through holes. Used a clip to hold wires and prevent them from going back through holes. Attached wires to new element and removed clips. Placed element bracket in place and discovered that both screws had stripped threads (due to years of vibration, I'm guessing). Rummaged through garage and found two screws that worked. Replaced back of oven and re-plugged oven into outlet.

TURNED OFF POWER to oven! Removed the oven racks to make work room. I unscrewed the two phillips head screws holding the element in place. Pulled the element out to expose the wiring clipped to the element. Pulled the wiring clips off the old element, clipped them onto the new element. Pushed the whole thing back into place in the back wall of the oven. Turned on power and checked to make sure everything was working. Screwed the two screws back in place. Baked a sweet potato and took a picture!

Used bic lighter to heat the screwsn and was easy to remove, no damage

Took out the old one and it on the new one. Bake element

I oedered a new unit matched with the Model Number! Installed .It did not work.They said Part amybe defectice.They quickly sent out another.That was installed and did not work.I contacted them again and they sugessted the Modular unit that regulated the Heat Temp. They were discontinued. They suggested I contact Corecentic Solution.com which I did.I am now in the process of shipping out my Modular Element to have it rebuilt. My stove is over 20 Yrs old .It inly costs me $110.00 to fix ourselves. Thank YouParts Select.com. You saved me over $1700.00 It would have cost to buy a new stove. They also gave me a full refund on the two units they shipped out. They are a wonderful helpful Company and will take care of your parts needs. Thanks Again Joyce

Shut off breaker to oven. Unscrewed the screws, disconnected the wires and removed the old element. Reversed the procedure to install the new part. Flipped on the breaker, turned on the oven and presto....the new element lit up! Appreciated your quick service. I will used Part Select again and will recommend to my friends.

Easy - I asked my husband to do it. He agreed that it was very easy. He unscrewed the old and took out the burned out part and inserted the new. Pretty much self explanatory. I wish all repairs were so simple. Thank you for having parts available.