Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water leak underneath dishwasher
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).
First I shut off the power to the dishwasher from the breaker panel. Then I removed the five screws holding the plastic top panel to the door (on the frigidaire, there is no need to remove the entire stainless steel door panel). I removed each of the four wires from the old latch (pulling the wires off required some "oomph") one by one and plugged them into the corresponding position on the new one. I did this so I would be sure to have them in the right place. I used a torx screwdriver to remove the two screws holding the old latch. I then replaced the old latch with the new one, replaced the top panel of the door, turned the breaker back on and everything was as good as new! The whole operation took maybe 20 minutes. It couldn't have been easier. The only surprises were how difficult it was to pull the wires off and the fact that the screws holding the latch were torx head.
In future, when I need parts, I will definitely use PartSelect. I have gotten parts from other sources, and this is the first place where, along with the part, you get all this advice from other DIY'ers. It's an absolutely brilliant idea and a lot of help.
the valve stuck closed - no water would enter the machine
remove vanity panel disconnect copper supply line from valve remove valve mounting screws rotate valve to access hose clamp loosen clamp and slide up rubber tubing about 2 inches pull hose off barbed fitting and remove old valve reverse order with new valve
This was pretty easy. It was a guess as to the problem, but there much debate , if the water isn't moving it had to be the pump, right?. So i replaced the circulation pump. 2 screws on the top and two trim screws on the bottom, and it slides right out. Then UNPLUG IT.. Take the screen out of the bottom on the inside and make sure you get all the water out or it will end up on the floor when you tip it on it's side. The directions were ok, i looked over them briefly but didn't use them. tools were, phillips srewdriver, torx driver (pump bracket srews) wire stripper/crimper (for the plug adaptor) and a heat gun, (for the heat shrink tube for the crimp connection). Overall it was pretty easy. the pump was made to be easy to replace. 45 min and back in action.
Took the dishwasher out removed the two screws and the part holding the motor in and removed the motor. Received the parts, places o'rings on the motor, which came with the kit, even though I ordered the two o'rings. Replaced the motor, installed the part that holds the motor and tightened the screws. Cut the old connector off the dishwasher and replaced it with a new connector that came with the kit. Reinstalled the dishwasher, works great. Thanks for your Site.
I closed on a house a few weeks back. You really don't notice issues with appliances until your living there....the walk through doesn't give you the time to really see anything hidden. Anyway - the dishwasher had appeared to be used to wash grease covered parts from a car so I pulled all the racks and filters out and placed the order for replacement parts. I saved hundreds in obtaining replacement parts verse buying a new machine - and I didn't have to sit around waiting for a repairman to do the work for me. I've made several purchases from PartSelect, and will probably making more in the near futre - Thanks!
took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.
For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .
First I removed the bottom dish rack to gain access to the spray arm. I proceeded by pulling straight up on the bottom spray arm, it disconnected with gentle force. The replacement part was not identical, so I determined that it would work by inspecting hole patterns and heat shield configuration. Then I gently pushed the new spray arm onto the water supply tube making sure that the spray arm snapped into place. Due to extremely fast ground shipping (less than 20hrs from order to my door) the repair was done within 24 hrs! Boy...was my wife pleased!
I disconnected the power to the machine. Removed the bottom access panel and screws holding the dishwaher in the cabinet opening so I could carefully slide the dishwasher out. Taking note of the pump position at the bottom of the dishwasher I removed the two wire leads, screws and hoses(pliers). I installed the new part in the reverse order and was able to run the dishwasher for a cycle while it was out to make sure there were no leaks. Dishwasher runs great and the dishes seem cleaner. Fingers crossed. Thanks.
I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the door, facing inside. The bottom screw on each side. Thanks for all the help.
This was too easy. I pulled out the bottom rack, spread apart the two clips which are at the bottom of the spray arm with my fingers and pulled out the old broken spray arm. The damage was visible. Then I took the new spray arm ( which looked different but still fit nicely) and gently pushed it into place. Done!
The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!