Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old spray arm had melted and wasnt spraying
I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!
I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes
First turn the power off! If you have water in the tub, use something like a wet/dry shop vac to drain as much water out as possible. Removing the strainers will help get more out. To remove the smaller horseshoe shaped strainer, pull up and towards the handle. The sprayer is then removed by rotating the base of it slightly. Then you can remove the large strainer. The more water you get out the better! Then remove the kick panel. You will see the drain pump right in front of you with a white and a purple wire. Disconnect the wires by pulling their tabs towards you, and move them out of the way. With a screwdriver, loosen the worm clamp on top of the pump that connects the drain line to the pump. Have a towel handy, even if you got all of the water out, there will still be some in the line. Then take a pair of pliars (long nose may work best, or small channel locks) and compress the clamp on the black hose behind the pump, moving the clamp towards the center of the hose. The pump should now move a little. Pulling the pump towards you, wiggle slightly to try to remove the pump from its support, preferably without breaking the tabs, but keeping them intact is not critical if you are replacing the pump. More water may come out at this point, so be prepaired. Put the new pump in by reversing the process, making sure you do not break the support tabs. Slide the compression clamp into place. Reconnect and tighten the drain line, reconnect the white and purple wires. Dry your work area carefully so you can spot any leaks. Apply power, and run a rinse cycle, watching for leaks. If everything looks ok, kill the power again and reattach the kick plate. Turn power back on one last time, and enjoy your dishwasher again!
The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job
Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.
Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks
Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!
DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.
Removed the clamp holding it to the floor and removed the c-clips holding element underneath and put new one in. Hard part was figuring out what was holding the element but since I still had the schematic drawing we figured it out. Saved a bunch on a repairman. After watching my friend install the new element I could probably do it myself next time.
I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.
FRIDGEADAIRE - GALAXY SERIES -Part arrived within 3 days of order BUT it was wrong part. All excited about getting the upper wash rack in full operation once again. Pilled shelf out to remove gasket to find it looked nothing like the one on there. The part I need is like a bellows of sorts that fits on the water line attached to the upper shelf. The part received goes on the back wall. Now i am back at square one with part I don't need and hoping for the part I do need
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.
Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)
Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.
Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.
Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks