EI23CS35KW0 Electrolux Refrigerator - Instructions

Cost of motor was 70% of complete ice maker. So I changed complete ice maker. Remove food from freezer. Remove ice drawer. Two screws and a four prong plug to change out complete ice maker. Use adjusting screw to assure water completely fills tray but doesn't spill, Suggest you set for less water an one a little each ice cycle until a full cube.

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

Turn ice maker off. Loosen two screws. Lift ice maker off. Pull plug apart. Remove icemaker. Plug new ice maker in. Mount to screws and tighten. Turn on ice maker. Then you can stop cursing icemaker..Fixed!!!!!

first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

Purchased a new ice maker assembly and installed. Very easy

before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Loosened 2 screws, slid the old ice maker up, disconnected power source. Revolved old ice maker. Reversed steps and was up and running in no time. Quick shipping too. Didn't pay extra and received it in 2 days.

Open box, peal plastic off of glass, slide glass onto shelf brackets

The diagram for the shelves is wrong I did not receive the right part. I ordered the crisper glass insert and received the vegetable drawer glass.

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

The repair was a piece of cake. After a previous day of hours being spent. This was the easiest repair ever. Thank You