EER2000M02WW General Electric Range - Instructions

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

My husband took care if it, very simple...took him less than 10 mins.

removed old element--had read warnings about wiring would go back into insulation--pliers slipped and one wire "jumped" back into insulation--had to take back off stove to retrieve the connection--other than that incident, the connection was simple--suggestion--make sure you have needle nosed vise grip pliers to prevent wire from becoming lost in the insulation---could not find my pliers so had to use regular pliers.

Removed old lower bake element on the inside by removing nuts at the back of inside of stove which holds element in place. Then removed metal guard panel on the outside back of stove to disconnect old terminals. Then from the inside of oven removed the old element and reconnected the new element terminals.

Easy to install replacement parts using the screws provided.

Making repairs on glass is not always fun to do especially when you have make sure what the right torque is.. My decorative glass broke and I reached out to part select for a new one. They had exactly what I needed for the perfect price. Not too difficult to replace just do not over tighten, this might cause the glass to break again.

Self-clean the oven or use Easy-Off. Lay some towels or other padded ragging on the kitchen table. Open the oven door and lock the hinges. Pull the door out of the oven and lay it on the table with the oven handle hanging off the edge of the table. The inside of the oven door will be face up on the table. Use the 1/4 Nut Driver to remove three sheet metal screws from the bottom of the door. Use the T10 to remove two long screws from the top inside of the door. lift the door guts and set aside along with the 5 screws and two spacers you found under the top of the door. Use the nut driver to remove 4 screws holding the Door Bottom Channel Trim. The door handle and side channels will fall off (catch and set aside). you are left with one piece of glass with the old bottom channel trim. Gently tap the lip of the channel with a screwdriver in a towel to slip it off the glass. Gentle patience is a virtue here or the glass will break. Clean the glass with CeramaBryte or equal to get the burnt oven goop off. (While you're at it, do the same to the bottom of the door guts above.) Slip the new bottom channel on the glass as far as it will go (not very far in my case) and replace the door handle and side channels. You will see that the holes line up pretty well without having to jam the bottom channel onto the glass. Screw (4) the side channels to the bottom channel. Replace the Door Guts, being careful to line up the two spacers at the top of the door. Three screws in the bottom of the door, then the two Torx screws back in the top of the door. Put each screw in just finger tight and after they are all started, screw them home. Slip the reassembled door back in the oven frame, flip the locks up and Voila! Now that it's over, let me just say that if a camel is a horse designed by a committee, this thing must have been thought up by the US Congress!

Unplugged the old and plugged the new one. replaced the covers and turned the power back on. No problems!!

I found that installing my element was far easier when I found this link it is a video on how to install this part It made it far easier to install correctly.

turned power off, loosing the to screws, left up and pull front, removed the two connection.placed new element inside oven fsten the two wires. push elemen, back in place, allaing screw holes tighten screw, turn power back on. Stove(oveb) working just like new.

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

replaced insulation

Instruction were very easy to follow.

Like the others, the element is easy to remove. Just 2 bolts. However, the wires attached to the element are very short on this appliance and if not extremely careful, they will pop back into the insulation. I was half careful as only 1 popped back. I secured the 1 wire with a small clamp and removed the central panel in the back of the range (5 bolts). I worked the wire back into the oven, attached both to the element, attached the element to the back of the oven, neatened the insulation in the back, and replaced the center panel. It wasn't difficult.

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.