EER2000M01WW General Electric Range - Instructions

Shut power off to stove. Removed two screws with a 1/4" nut driver. Extracted the old element. Discovered one of the two solderless connections was not connected. Pulled the stove out and removed the back panel, only 4 screws, and exposed the wiring to the element. Discovered a wire connection had burned out. This was most likely due to a loose connection. I installed the new element and made the good connection. After cleaning up the burnt wire end on the other wire, I installed a new crimp terminal and connected it to the element. These crimp connections need to be tight. Replaced back panel and plugged stove back in and tested it. All worked fine. Put stove back in place. About 30 minutes. I am an electrician but do not normally do appliances. Good luck.

Man..this was easy. I'm no Mr Fix-it, and had actually left a message with a repair guy to come and replace the fried oven(bake) coil. After doing a Google search, and seeing the video by the PartSelect guy, I said, "hey I can do this". I ordered the part, it came wrapped better than my first born child, and it was a breeze to install. My wife is still in shock that I did it!

Only had to take out 2 screws and 3 bolts, the new glass slid right in, there was alittle trouble lining up the bolt holes when puttung back together but that wasn't even realy that bad.

Unpluged the unit from the electrical outlet,unscrewed the unit from the back wall. I used electrical tape to hold the wires so they wouldn't go back inside the stove. Replaced the unit with the new one. Pushed the prones into the unit,put the screwes back and in now time i was finished.Quick and easy job for a lady.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

I had read some accounts of the terminal wires pulling back into the insulation, and, sure enough, one of them did before I could clip it. Even at that, pulling the stove out and removing the four nuts that held the shield in place only added another five minutes, tops. The whole thing took less than 15 minutes to change. One nut driver removes the two nuts that secure the bake element to the back of the oven, and also fits the four nuts on the shield on the back of the stove. Very easy repair, thanks to the advice given by others on this site. Thanks.

1. Pull range out from wall and disconnect power cord from outlet. 2. Remove 5 screws to remove panel on back side of range to expose the bake element connections. 3. Pull push-on terminals from element. 4. On inside of oven, remove two screws and remove old element. 5. Insert contacts end of new element through the holes in oven back wall. 6. Reverse the disassembly steps to complete the installation.

Installation instructions on the partsdirect site were great. Unscrewed the (2) hex head screws that hold the element and used clamps to hold the terminal ends from recoiling back into the insulation of the oven cabinet. Put the push on terminal ends on the new element, tightened screws and done. The $50. Part fixed the problem and delayed another range purchase.

We emptied the bottom drawer and pulled out the stove, unplugged it and my wonderful son came over and installed the part in about 15 - 20 minutes. The part came without instructions, so we were glad he was around. I am glad we were able to find your service. Thanks.

After reading on the website of others doing repairs I was able to fix my oven easily. I removed the two screws on the back wall of the oven. I carefully pulled the element forward bringing with it the connector wires. Before sliding them off of the old element I made sure that they were pulled out far enough so not to loose them in the insulation. I removed the old element. Slid the connector wires on to the element. Carefully slid the element back into the back of the oven. Put the screws back in and I was done.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

First I turned off the breaker to the oven, then removed the oven racks. I removed the two small bolts that hold the element to the back wall of the oven. I then gently pulled the element out to expose the terminals, with needle nose pliers I carefully removed the clips without letting the wires slip back behind the oven wall. Then I pushed the clips onto the new element and bolted it back onto the oven wall. I turned the breaker back on and preheated the oven and it worked like a charm.

just purchased new knobs. The price was great, just took a little longer to receive then anticipated though.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Parts Select delivered my item quickly and in good condition. The replacement of the baking element was very easy. The following seven steps took less than 10 minutes to complete: 1) Pull the stove from the wall and unplug the oven (This was a great opportunity to ensure the floor area was clean and free from food particles) 2) Use Pliers to remove the back panel covering 3)unhook the bake element from the wire connections 4) Remove the bake element and replace with new one 5) reconnect new element prongs to wires 6) Replace back panel 7) Plug stove into the wall and push stove back to wall. Now I am ready just in time for the holiday baking season.