ED5KVEXVQ00 Whirlpool Refrigerator - Instructions

exactly as your video described, it was just that simple. Now it's on the the ice maker that don't work. You have a troubleshooting video on it? lol Thanks you were a great help.

The push on fittings made the replacement much easier than I expected.

removed insid back and replaced the fan. no tools needed inside. very easy

Found the part on the website (be sure to put the proper model number in)Be very watchful ofhow the bdracket come out and how the various wires go back onto the bracket. (Make a diagram on paper with colors in the proper location.

I watched the PartSelect Video on removing and replacing the auger drum. I replaced the ice auger also. Super service from PartSelect.

Just had to take the old one out and put the new one in. No problem.

Took the new chut set it into the ice dispensing openening,then cliped in place,End of repair.

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

Found auger was broken. Also found the ice cubes seemed too big and not breaking apart after the ice maker would cycle and dump in to the bucket. So I adjusted the ice cubes water feed timer making the cubes smaller and they are working real good through the auger now.Thanks for delivering the part so fast.........

Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.

Turn off water supply then Remove the dispencer trim by putting a flat screw driver into the slots at ths lower edge of trim and push down on trim as you pry the trim out and remove trim. Remove two screws holding the controls and unhook the far right connector and push to the side to get to old line,unhook the connecter at the bottom of door and remove compression nut from old line,remove the screw holding the old line in place and remove the assembly by pulling up and out. install new metal holder into slot and install screw to hold in place (If you have old style)cut new line at angle (Don't cut but about 1/2 inch off) and push new line down through hole at the bottom of the door where old one was and install the upper end into new metal bracket notch ,reinstall control panel with the two screws that were removed making sure that the controls strike the switches correctly ,reinstall the trim ,cut off the line to the match the connector and install the compression nut and put lines together,turn on water and check for leaks. Test and remove air and job should be complete. (hardest part was getting the trim off with out breaking it, I looked close and found the notches on the bottom)

All I did was removed the stickers and place it in the frame - no tools required. It fit perfectly and is since it is clear (the original one has a grid pattern in it) I can easily see everything in the drawer below. I will be more careful in cleaning this one - apparently the temperature difference from cool to warm caused it to break, so I will just wipe this one down rather than submerging it in water.

I printed your diagram of the complete assembly for reference when installing the new part. I was able to get the part number from the diagram and ordered it online. I received the new part in 2 days. I removed the ice from the ice maker's bin and kept it in the freezer. I removed the old drum and auger from the ice maker assembly and installed the new drum #4388736. I looked at your diagram to make sure I had all of the blades in their right orientation. After the drum and auger assembly was installed, I placed the ice that I had saved into the ice bin and slide it back into place. I then tested if the assembly would now drop ice and also if it would crush the ice, which i do not use very opten, because I know that using the ice crush mode will prematurely wear the drum assembly. The drum and auger gets much more stress when it is crushing ice. After the icemaker worked flawlessly, I rolled the refrigerator back into its regular position along side the cabinets. I was very pleased with the part and the excellent service that PartSelect.com provided. The price was less than I thought I would have to pay. Also, the company provides most of the individual parts of the ice maker assembly. Normally, when I would shop at a designated Whirlpool distributor, I would have to purchase the entire assembly costing 3 or 4 times higher than the price of the individual part. I, will now, always purchase my parts from PartSelect.com.

You guys have this for me the next day

My son took a plastic panel off the top front of the refrigerator. He found what looked like a four by four mother board type part. After looking at it he seen there was a part on it that definetly looked burnt.I got on the internet and did a search and found your site. I took a shot in the dark that this was what was wrong, looked up the part and ordered it. I had the part in two days. He installed it and BINGO, the refrigerator now works fine. Thank-you for all of your help and fastness on the delivery of the part! :) AWESOME!!!!!!!