ED2KVEXVQ01 Whirlpool Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water did not work
removed front of control to find the control board broken. The switch was working ,but the broken part of the board would not allow the switch to work.
Parts Used:
-
mark from Blaine, MN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Valve was leaking into ice maker
Followed on line instructions when searching for repair of water inlet valve for Kitchenaid refrigerator. Perfect instructions and an easy fix.
Pulled fridge out. Turned off water supply. Removed cardboard backing on bottom rear of fridge. Removed old valve on right hand side. Removed hoses by pushing in on the rings and holding then pulling out hoses. Installed new valve being sure to push hoses the whole way into vale. Turned on water to check for leaks then replaced cardboard. About 20 minutes total.
Keep some towels ready for the water that comes out of the hoses. Don't worry about matching hoses, they are different sizes and easy to identify. I recommend removing the entire cardboard backing of the fridge so it is kept in good condition.
Pulled fridge out. Turned off water supply. Removed cardboard backing on bottom rear of fridge. Removed old valve on right hand side. Removed hoses by pushing in on the rings and holding then pulling out hoses. Installed new valve being sure to push hoses the whole way into vale. Turned on water to check for leaks then replaced cardboard. About 20 minutes total.
Keep some towels ready for the water that comes out of the hoses. Don't worry about matching hoses, they are different sizes and easy to identify. I recommend removing the entire cardboard backing of the fridge so it is kept in good condition.
Parts Used:
-
Robert from Downingtown, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water dispenser wasn't working
called in a repair company and they wanted to charge me $350.00 to repair it so I went on line and found some people had replaced the control bracket, so thought what can I loose? Ordered the part and replaced it within about 30 mins. Now it works perfectly!
Parts Used:
-
Elizabeth from Dallas, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaking under refrigerator
Watched the video, took the backing off of lower part of refrigerator. Unhooked the parts just like the video showed, put new part in, and shazam! It worked!!
Parts Used:
-
Tammey from Milaca, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the part went bad and needed to be replaced
-
Peter from Pahrump, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bin broke
Replaced bin - very easy. I could not believe how fast you guys got me the part :)
Parts Used:
-
Linda from Novato, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting no water from door
The bracket that held the micro switch had broken, I had to replace the cover brace assembly. The job went smooth.
Parts Used:
-
Gary from Citrus Heights, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The tip of the bottom tab was too long to fit through the slot for it.
I used a sandpaper drum on my Dremel tool and ground about a millimeter off of the bottom tab tip. That allowed me to then push it through the slot and rotate it up and closed the top clips to complete the job.
Parts Used:
-
Jerry from Orange, TX
-
Difficulty Level:Difficult
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken ice shute
I pulled the broken shute out because one locking tab had broken. The front tab slipped out very easy. I slid the new piece into position by placing the front tab into position and press the two locking tab into place and it snapped on. Took about 3 minutes to do everything.
Parts Used:
-
Willie from San Antonio, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower Door Closing Cam worn out.
Removed top cover, then removed top hindge pin plate, then removed the door. Replaced the Lower Door Closing Cam, Reinstalled door and hindge pin plate and cover.
Parts Used:
-
Laura from Lake Havasu City, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clip on ice guide broke and guide was loose
watched the repair video on parts selct site which confirmed my thoughts about the repair procedures. Followed the simple instructions and used a little dab of vasaline so the plastic on plastic clip slipped into place easier. Simple repair. Parts were shipped fast and cost was good. New guide was in place and working less than 1 week after I ordered the part. Great and fast shipping. Would use this site again without hesitation.
Parts Used:
-
James from Whitewright, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Micro Switch Holder
Simply, removed covered took off parts, and replace on new part, rehooked replaced cover. It is a bit tedious removing the cover on the ice dispinser but it is slotted at top, sill pop off easily but be careful can break if you force it.
Parts Used:
-
RICHARD from SAPULPA, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken vanes in ice bin auger
Ordered part, watched video. Had a problem with reassembly of ice crushing assembly, did a re-do as one of the blades had dislodged from the drive shaft!
Parts Used:
-
Robert from Lantana, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic broke so ice would not move to blades
-
Phyllis from Prague, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom lug broke off
Just follow the video on the website. Great instructional video. Ordering and delivery was excellent. FedEx is my favorite delivery service. I do a lot of purchasing and Parts Select was the easiest. Website is well thought out and simple to use. Emails keep you informed of the order status.
Parts Used:
-
Gary from Pelham, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!