ECBP82SK1SS General Electric Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replacing lower element
removed old element--had read warnings about wiring would go back into insulation--pliers slipped and one wire "jumped" back into insulation--had to take back off stove to retrieve the connection--other than that incident, the connection was simple--suggestion--make sure you have needle nosed vise grip pliers to prevent wire from becoming lost in the insulation---could not find my pliers so had to use regular pliers.
Parts Used:
-
Kathy from McRae, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Old bake element burned out
Removed old lower bake element on the inside by removing nuts at the back of inside of stove which holds element in place. Then removed metal guard panel on the outside back of stove to disconnect old terminals. Then from the inside of oven removed the old element and reconnected the new element terminals.
Parts Used:
-
Janos A from Westminster, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Range lower drawer would not stay on track.
-
Richard from Newark, DE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Old element burned through.
Unplugged the old and plugged the new one. replaced the covers and turned the power back on. No problems!!
Parts Used:
-
Charles from Licking, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Bake Element stop heating up
Turned circuit breaker off to range as recommneded. Removed 2 screws from old heating element using a nut driver after removing the two racks from inside the oven. Considereing others had noted the wire sometimes came off and had to be retrieved by removing the back panel, I removed the back panel using the nut driver instead of waiting to see if that would happen. I removed the back panel after sliding the range out for easy access. Back panel was removed using the nut driver on approximately five screws that secured the back panel. This step may not have been needed because the wires were secured snug on the heating element. Secured new heating element and back panel. Turned on power after tripping circuit breaker and noticed a bright red hearting element in range within one minute. Real simple repair quickly done minutes after delivery by UPS.
Parts Used:
-
KEVIN from SUFFOLK, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven was not heating up. Broiler worked but not bake elemet.
We pulled the stove out, unplugged it, unscrewed the old element and screwed the new one in.
Parts Used:
-
Barbara from Plymouth, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
gasket leaks heat from oven
pull gasket from door bottom and pull gasket to release retainers in door frame. refit new seal in retainer holes and push gasket into slots at bottom of door. done perfect fit.
Parts Used:
-
ROBERT from SLIDELL, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bottom element burned up
Extremely easy, two screws pull connection inward to oven grasp push pin pull disconnect (don't let go of oven end or it will recede into appliance) push pin new connection on two connections. Remount with two screws and job was done! And yes a woman repaired her own oven very easy!
Parts Used:
-
Cheryl from Ferndale, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Missing oven racks
Ordered the racks then put them in when they arrived.Correct parts got here when Pat Select said they' be here.
Parts Used:
-
charles from tonopah, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!