E23CS78HPS3 Electrolux Refrigerator - Instructions

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

The repair was easy. After looking at the diagram and locating the part need i just ordered it. But I wish I had taken the door off before ordering as I really need a second part. So resulting in extra shipping cost. Parts that were needed were 240328201 and 240457702. Tks Jim

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

Purchased a new ice maker assembly and installed. Very easy

before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

It was simple... After paying $280 for a repair man to come out and install some unnecessary part to the fridge when I told him "everything on the Internet points to a thermostat repair." He disagreed, fixed the fridge and said the freezer would work more efficiently now. It didn't, so I bought a new fridge/freezer, put the old one in the basement. I ordered the thermostat (under $20), put it in, and now (knock on wood), works great and I have a beer fridge for the man cave

Removed the door's top hinge support by removing two hex bolts. Lifted the door off of the bottom hinge and laid it out on the dining table. Removed the old hinge bearing from the bottom of the door and replaced it with new. Installed the door and refastened the top hinge bracket. Note that there are two hinge bearings that mesh with each other - one is attached to the bottom of the door itself and the other attached to a bracket on the cabinet (part 13). As long as you have taken the door off, replace both hinge bearings. You may need some help from a second person to hold the door in place when the top hinge bracket is removed.