E23CS78EPS1 Electrolux Refrigerator - Instructions

watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !

Turn ice maker off. Loosen two screws. Lift ice maker off. Pull plug apart. Remove icemaker. Plug new ice maker in. Mount to screws and tighten. Turn on ice maker. Then you can stop cursing icemaker..Fixed!!!!!

first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

Easy to install (self explanitory)

before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

I removed the top hinge cover, loosened the hinge so I could remove the door and laid the door on it's side. I removed what was left of the Door Closing Bearing and istalled the new parts. Set the bottom of the door on the lower hinge then postioned and set the top hinge into place and tightened the top hinge and installed the hinge cap.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

It was simple... After paying $280 for a repair man to come out and install some unnecessary part to the fridge when I told him "everything on the Internet points to a thermostat repair." He disagreed, fixed the fridge and said the freezer would work more efficiently now. It didn't, so I bought a new fridge/freezer, put the old one in the basement. I ordered the thermostat (under $20), put it in, and now (knock on wood), works great and I have a beer fridge for the man cave

Followed video instruction provided on this site.

Easily found the parts we needed from the diagrams, Hinge bearing and door closing cam, watched the video, which was very helpful, ordered the parts from the parts list numbers...Our order came in just a few days and my husband put the parts on in about 20mins. Couldn't have done it without the help we found on your page...Thank you so much....Will be back if we have any other trouble.... Bill and Ellen Lopitz.....

The repair was so easy, it took me longer to find the nut driver to loosen the screws than it did to replace the unit. Just remove the ice bin, back the two screws out enough to lift the ice maker up and off, unplug the power connector. Install the new one in reverse order. One thing to keep in mind is the freezer needs to be 5 degrees or below before the ice maker will cycle. Took less than 10 minutes to replace.

watched youtube video on this repair that helped a lot.Remove tray and front plate - gently pull out ribbon wire that connects to front plate.I warn you not to screw back plastic pieces too tight - I broke some plastic that I had to glue back. I did job without removing water tube from mechanism - it pulled out just enough to reach screws holding actuator - also it is a bit difficult to push back ribbon wire that connects into front plate. test before screwing mechanism back -ribbon wire must be reattached to test

Received the parts promptly and did the repair just as the video showed. All went well and had the repair completed in 10 minutes. For me that was remarkable because I have two left hands! Would highly recommend partselect.com

Called repair person, 80.00 to come look at it. Deceided to see if I could find part on my own. Surfed the net found this website, ordered the part for 5.00, total 13.00 including shipping. waited a few days, received part in mail, lifted refrigerator door off hinge, inserted the part. Works like new. 80.00 plus repair, cost me 13.00. Amazing