Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E23CS75DSS4 > Instructions

E23CS75DSS4 Electrolux Refrigerator - Instructions

All installation instructions for E23CS75DSS4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the E23CS75DSS4
211-225 of 394
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice would not release

  • Customer: cathy from Columbus, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
To describe this replacement as "really easy" is an understatement! The hardest part was digging the socket set out of the tool box. The instructions were well written, as were descriptions of fellow home do it yourself types. Those gave me the confidence to just for it. I am so tickled with myself and the money I saved! My hubby is pretty impressed too! Cathy

The Door Closing Cam had crumbled

  • Customer: Vann from Kennesaw, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.

No Ice, No Water

  • Customer: Caroline from East Amherst, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

Freezer leaked, no water disp. & Crusher didnt crush

  • Customer: Edith from Langhorne, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First I defrosted the entire unit, both sides for 24 hours. Restarted, I now have water dispensing. (It had apparently frozen) Next I took out the ice crushing part and took it apart, (a few screws) by removing the broken floppy piece; the small plastic floppy door that allows ice to crush, replaced this small piece, rather than replacing the entire big plastic piece that I ordered. Used a slot screw driver removed the old floppy piece that was broken and removed the same piece from the new one and switched them out. Reassembled the entire unit (a few screws), put the ice back in and it works great. I got the instructions for taking apart this from this site, however, it was fairly easy to figure out. Just be patient with the plastic parts.

Maker would not make ice

  • Customer: Cecil from Blaine, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I suspected that the On/Off Switch was the problem. (Pressing and holding the switch 'on' for 15 seconds to recycle the icemaker did not bring the ice level control arm to life.) I decided to replace the whole icemaker rather than just the switch. (Do not try to replace the switch...almost impossible.) Steps: 1/Remove the Icecream shelf (lift up the front lip and pull out; 2/remove the Icecube holder tray (lift up the front and pull out.) 3/Remove the two hex head screws which are facing you above the ice maker. 4/Pull the icemaker slowly out and and down to reveal the electrical wiring, and unplug the electrical plug. 5/Follow new instructions re the water hopper and the ice-flapper-thingy on the new icemaker, and turn the new switch to 'off' before you start to install it. 6/Plug in the new icemaker, and push the electrical wiring down to the left as you push the icemaker into place, make sure the back edge of the water hopper goes under the water spout. 7/Replace and tighten the two hex head screws. 8/Press and hold the switch 'on' for 15 seconds or more to cycle the icemaker (the ice level control arm will slowly raise up and then go back down). 9/Replace the Tray and the Shelf. 10/Allow the icemaker time to cool and freeze the newly injected water.(This may take up to 6 hours.) 11/Listen for the sweet sound of the dropping icecubes.

water dispenser/ice maker inop

  • Customer: Michael from White Springs, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

support broke

  • Customer: Lisa from Mena, AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just put it in the old hole. the hard part was getting the old one out. you have to poke the center piece in to remove. otherwise you will break your fridge. then you have to to pull the center piece out before you put new in.

refrigerator staying to warm

  • Customer: nicole from chipley, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
husband did it took only a few min part was easy to find

Snapping sound on refrigerator door side when opening and closing door.

  • Customer: Juan from El Paso, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Unscrewed the top hinge, lifted door and laid it down. Took off old hinge bearing and snapped new one in. Put door back and no more noise. Easy fix. Only problem was that I couldn't believe I waited so long to fix that simple problem.

water valve leak

  • Customer: Donald from Wilmington, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

broken suport for pam

  • Customer: JORGE from HOUSTON, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
take of the tray & take parts out & installed the new ones

Replaced Water Inlet Valve

  • Customer: Robert from Arlington, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

water wont dipense and no ice

  • Customer: silvestre from san clemente, CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

Fridge was freezing items & freezer was not freezing items

  • Customer: JEFFREY from York, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
It was simple... After paying $280 for a repair man to come out and install some unnecessary part to the fridge when I told him "everything on the Internet points to a thermostat repair." He disagreed, fixed the fridge and said the freezer would work more efficiently now. It didn't, so I bought a new fridge/freezer, put the old one in the basement. I ordered the thermostat (under $20), put it in, and now (knock on wood), works great and I have a beer fridge for the man cave

Refrigerator door made popping sound when opening or closing

  • Customer: Satish from Mt. Laurel, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Removed the door's top hinge support by removing two hex bolts. Lifted the door off of the bottom hinge and laid it out on the dining table. Removed the old hinge bearing from the bottom of the door and replaced it with new. Installed the door and refastened the top hinge bracket. Note that there are two hinge bearings that mesh with each other - one is attached to the bottom of the door itself and the other attached to a bracket on the cabinet (part 13). As long as you have taken the door off, replace both hinge bearings. You may need some help from a second person to hold the door in place when the top hinge bracket is removed.
All Instructions for the E23CS75DSS4
211-225 of 394