DU4K Magic Chef Dishwasher - Instructions

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

romoved 3 screws, removed spray arm support nut. pulled off spray arm support, replaced new spray arm support and spray arm support nut

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

first i unhooked the 2 hoses then removed the 2 screws holding the valve in place, I then removed the hose fitting from the old unit and installed it on the new one. I then bolted on the new valve and reconnected the hoses and it worked fine.

Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Pulled out the old gasket and pressed in the new one. No more leakage.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

On my dishwasher, one linkage broke, making the door feel heavy to raise and lower. Because there are two door springs, one on either side, I decided to replace both plastic linkages even though only one broke, because it would only be a matter of time before the other plastic link failed and I would have to do the repair all over again. Remove the 2-piece panel at the bottom front of the dishwasher. It's held on by four hex-head screws which also have slots for a Philips screwdriver. The springs can now be seen on both sides of the door, at the bottom. Remove two screws that anchor the dishwasher to the underside of the counter. Gently ease the dishwasher a short distance out from its under-counter recess, just far enough to gain access to the springs. Make sure not to put any excessive strain on the water inlet tubing, drain hose or electric power cable by pulling the dishwasher out too far. Close and latch the dishwasher door so that the springs are in minimum tension. Note the slot that the linkages hook into on the door levers. Hook the small end of the spring into the hole in the metal bracket. Slide the linkage onto the other end of the spring. Stretch the spring to slide the free end of the linkage onto the door lever and into the appropriate slot. Push the dishwasher back into its recess and replace all screws and panels.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.

I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone

I took off bottom front and kick plate. Retrieved the spring which had flown to the rear of the unit. Cannot pull unit out because the trim piece on the counter top was put in after the unit was screwed to the underside of the counter. So... I noticed that you could move the plate the bottom of the spring hooked into by unscrewing a long quarter inch hex head bolt and bring the plate forward where I could hook the bottom of the spring into the plate. I had first hung the door spring linkage on the door (looked at the opposite side to see how it was arranged) then onto the top of the spring. The difficult part was keeping the bottom of the spring in its hole in the plate while moving the plate back in place. After I got it past the flange where the bolt screwed in, I screwed the bolt in and pulled the plate back to match the opposite side distance which put tension on the spring. The door now works. I am fortunate to have my husband's tools available.