DU40JV Magic Chef Dishwasher - Instructions

We simply removed the old gasket which was corroded, cleaned up the hard water buildup, and popped the new gasket into place. The problem was fixed! No more leak!

Removed two lower panels using nutdriver. Ran washer through a rinse cycle, to determine for sure where leak was coming from (under door on left). Examined the door gasket and observed buildup of lime deposits and a general depression of the gasket through years of use, especially in lower portions. Removed the old gasket observing how installed. Cleaned out groove with Lime-away and toothbrush. Washed clean using water in a squirt bottle. Dried things out using paper towels, and then pressed new gasket into place, starting at lower left. Readjusted the gasket to fit precisely end to end. Shut door and ran a drip free load.

I first changed the dispenser door latch grommet, which was very eazy except for the left side nut screw which was a little awkwaed to get to with the nut driver. Not a big problem but difficult enough that i stripped the threads (plastic) and had to get a larger screw which is working fine so far. Since the grommet didn't stop the leaking although it was obvious it was leaking from the soap trail. I ordered the gasket and got it very promptly put it on and guess what. Still leaked some. I discovered when they installed the dishwasher the door appeared to be warped. To fix this there are two door tension springs under the bottom panel. By adjusting these with a log screw driver problem finally solved.
It is good to have not only a great place to get parts but the idea's from others are terrific. Although this washer is 15 years old it looks new and now acts new. Thanks so much for good service and advise.

Lifted out the old rack and set in the new one. The raised portion of the new rack was not high enough to clear the lower spray tower, so I adjusted the back wheel "axles" downward about 3/8" with pliers, which raised the rear of the rack enough to clear the tower.

Even though there was plenty of water pressure from the pump, the lower arm would not spin. I could move it with my hand but there was too much friction for it to spin. Turns out an item named seal ring[38] (I would call it a slip ring) had become dislodged somehow at the interface between the rotating parts and the stationary parts but I did not learn that until I was able to disassemble it. I could see from the diagram that there were threads at the top of the SPRAY ARM SUPPORT[39] that engaged with the threads in the CENTER SPRAY NOZZLE EXTENSION[33] so I held the arm and tried to unscrew [33]. CRACK! The 4 thin plastic arms in [39] snapped right off. I then disassembled and found the dislodged seal ring[38]. I concluded that I would never have been able to disassemble without breaking [39] due to the calcium in the threads (even with repeated applications of vinegar or lime away): the plastic arms are just too wimpy. But the price of a new [39] was a bargain, I was amazed. Came in 2 days, I re-assembled, now the spray arm spins freely and the dishwasher works again. I will try to remember to use vinegar periodically incase the slip ring dislodges again. This has been a great dishwasher otherwise IMHO( and a bargain price).

Removed the old gasket, without tools, and fit the new gasket into the space, making sure it was in the groove correctly all around, job done, works great. The ordering of the gasket on this site was easy and the shipping time was amazing, one day. Would use this company again, and recommend to anyone needing parts that wants to do repairs themself. I am sure saved a whole lot over hiring someone, and got the job done sooner also.

1- turn power off. 2- remove 7 screws to take door apart 3- remove 2 screws to take dispenser out. 4- i unhooked electic plug from it. 5- replace grommet and all back together. not bad to be 72 years old.

The part arrived sooner than I was ready to install! But it only took about 30 mins.(could take less but I like to do extra) I used a cordless drill with a star bit to remove the 7 screws holding on the inside plastic door cover. I unplugged the four electrical plugs so I could take the cover off completely. Once removing the cover I placed the cover on the kitchen counter to work on. I removed the liquid softner dispenser by turning tthe big threaded white plastic gromet on the front side of cover. I checked the big o ring for wear. Before reinstalling the liquid dispenser I placed a bead on 3-M black gasket silicon around the base and placed the o-ring on top of it just to make sure that it won't leak either. (this is installed last) There was quite a bit of the calcium build all over the parts. I cleaned this up with some CLR and a toothbrush, you don't have too but I'm a little picky and do not want to open it up again.
There are 2 little hex head screws holding the latch and associated hardware in place removing them was no problem. remove the old rubber gromet and put the new one on. Make sure the area where the gromet seats is smooth and clean. Now put it all back together and you should have no leaks

1) Remove the lower dish rack.
2) Use towel to soak up any water in the dishwasher.
3) Remove the bottom plate on the dishwasher front.
4) Remove clamp from around the discharge hose. Some water will drain out so have towel handy.
5) Dishwasher will need to be pulled out from its built-in area in order to feed the old discharge hose out and the new one in. MAKE SURE THAT THERE IS ENOUGH PLAY IN THE ELECTRICAL WIRES AND THE INPUT WATER LINE TO THE DISHWASHER TO ALLOW IT TO BE PULLED OUT.
6) Loosen, all the way, the white plastic locking arm that clamps the pump housing. It clamps on a white corrugated plastic piece.
7) Remove the spindle arm inside the washer by unscrewing the "tower" piece.
8) Remove the screws from the pump housing on the inside of the washer.
9) Lift the pump housing carefully and remove the rubber gasket from around the housing. There is enough play to remove the gasket and put the new one on.
10) Clean the area around the housing so that the new gasket seats properly.
11) The new gasket will have to be installed before re-installing the discharge hose.
12) Re-install screws in pump housing.
13) Re-install the spindle arm.
14) Tighten the white plastic locking arm underneath the washer that locks down the pump housing.
15) The new discharge hose can now be reconnected between the sink drain and the dishwasher.
16) Dishwasher can now be put back into its place.
17) Before closing up the bottom plate of the dishwasher, it should be run and checked for leaks before finally closing up. My advice - let it stand overnight before checking for leaks. after running.

My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.

Our dishwasher got to the point where it would not complete a wash cycle. I found that by jiggling the door latch, the dishwasher would whir back to life. For awhile, if I put a clothespin on the door latch, somehow enough pressure would be put on the switch to keep the dishwasher going. Finally, the dishwasher refused to cooperate...so I ordered a replacement switch.

The repair was easy. I only had to remove the interior door panel, unscrew the metal bar at the top of the door and underneath the door panel, then remove the black plastic shield. After that, it was just a matter of wiggling the old switch out and wiggling the new switch.

CAUTION: Be very sure that the power to the dishwasher is turned off. I got a scare because I thought the circuit breaker was off, but I had flipped the wrong one and suddenly, with my fingers very close to the bare connectors, the dishwasher came back to life briefly. I ran downstairs and found the correct circuit breaker and all was fine after that.

Take the bottom skirts off of front. Put drain solinoid back in its bore and secure with wire or a rubber band.It will be a chrome cylinder hanging Take the center spray section out and look for the broken lever. Get both pieces out if it split and fell in two. Mine usually crack and stay on the shaft. Pull the circlip off and slide new lever in place and replace circlip. Re-assemble center section. If you are going to keep the dishwasher buy extra levers. I buy them 2 at a time and try to keep a spare.

Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

removed spray head, pulled motor/pump assembly. took apart impeller housing and then removed motor and pulled impeller off its shaft, the most difficult part was actually pulling off impeller from the splined shaft. I actually broke old impeller in the process. The good thing is that the new seal came assembled with new impeller so that was not a problem. After re-assembling everything it worked fine and still works for a week since repair.