DSS25PFMCCC General Electric Refrigerator - Instructions

I decided to replace my ice flap while replacing the solenoid. It was easily done while the face plate and control panel were already off. The problem I encountered was that the flap did not seal properly, thus I ended up with frost in the ice chute and on the ice box so the ice would not come out. Also, the water dispenser would not work because it froze up from the cold air coming out of the ice flap. I got another flap, but had the same problem. Finally adjusted the spring that helps hold the flap closed. That helped but there is still not a tight seal.

had to take the handle off the old drawer and snap into new one be careful not to brake the handle getting it off the old drawer

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Slip the front cover off by gently pulling down, carefully un-plug the wire connectors (x3), remove 4 screws and remove paddle assembly. 2 screws hold the flap on and 3 hold the solenoid. Replace the screws with stainless so they won't rust. I tried coating the solenoid in lithum grease to prevent rust, onlt time will tell if it works.

I just follow to the video and take step by step. It's was very helpful and easy. Thank you.

Removed the Control Panel and the outside of the Dispenser Outlet. Removed the Flapper Door and the solenoid. Replaced both parts with new parts, and re-assembled. The pin, at the top of the Solenoid was badly worn and the plastic arm was very rough on the surface adjacent to the worn pin.

Removed old slides and installed new slides.

Replacement was simple. Remove the drawers. Suspend the cover pan glass with masking tape to keep it above the rail. With a 1/4" nut driver, remove the two nuts that hold the drawer slides in place. Remove the old slides and install the new. Remove the masking tape from the cover pan glass and replace drawers.

I followed the video. Everything was extremely easy, but I am 74 years old, have never repaired anything, and have arthritis in my hands. When I got to the step where I had to push in on the tabs, I couldn't do it. I had a friend push in while I pushed up...voila! But it took two of us. I also had a little trouble putting the spring back as it had been a few days since I had removed it. For us beginners, Steve, close-ups of things would be useful. I LOVE this site, however, and will use it again. You saved me over a hundred dollars! (I know because this lousy part has broken twice before.) Now that I know its name, I will not be crushing ice anymore.

Turned the water off to the refrigerator. Pulled the refrigerator away from the wall opening. Removed the back lower panel. Removed the lines to the water valve. Removed the electrical connections. Installed the water lines on the new valve and verified they would not pull out of the push in connections. Installed the electrical connections. Turned the water on and checked for leaks and proper operation. Reinstalled the back panel and positioned the refrigerator in it's proper position.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

After recieving the water pump and ice maker repair kit,i had my laptop on the counter. Your video of Steve the repair man made the job extreamly easy. Your concept of ordering and repairing is awesome! Thanks.

per instructions supplied with main electronic control board. was much easier than I thought it might be.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....