Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The wire mesh on the lint filter separated from the frame and lint was getting inside the dryer.
Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1
unknown 25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.
1. Before we started anything we unplugged the dryer and disconnected the vent. 2. We removed the top and loosened the contol panel on top. 3. We removed the front. Be careful of the wires. You can label them, or just remember where they go. 4. Lay the dryer down on it's back. This make's it easier to remove the drum. 5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it. 6. Once the drum was removed, we removed the screws from the inside of the drum. 7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description) 8. We screwed in the new "top" and put the dryer back together.
Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.
Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.
Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.
Dryer was very noisy. After I replaced the belt I noticed the bearing assembly was shot.
Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.
Removed the screws that hold the draying unit (barrel) to get accest to the back of the switch, and that's when I noticed that I will need the belt and I ordered to when my existing belt goes I have a replacement.
dryer would make clunking noise and sometimes a scraping noise
I looked on the internet for instructions to take the dryer apart,took the parts out one at a time ,and replaced them.It was easy and it made the dryer quiet again.I could see the obvious wear on the parts.I was happy to save the money a new dryer would cost.
Opened door and found recessed screws that screw into the top of the dry and removed them and then the front removed very easy. Then took of the plate on the back of the dryer to get to the pulley that the drive belt was on and took the belt off the pulley. The dry drum then slid out very easy, there was 2 of use which helped with the ease of getting the drum out. We replace the bearing and the idler pulley wheel. Vaccummed the lent out and then put it back together. Now it is squeek free.
First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.
the plastic stem fractured off the starter so the starter could not be turned on
Removed the back off the control panel. unclipped and unscrewed the starter and replaced with the new starter, replaced the back of the control panel. Very easy and the part was mailed and arrived the very next day! Thank you
something was sent on top of dryer, fell and snapped knob of at the neck of it.
unscrewed top cover,disconnected wires,took out part ,set in new part, put wires back on and closed up top with cover. I have had to replace other parts to my washer and dryer and have been very pleased with the parts fitting and also the speedy delivery, always had them between 2-3 days.
