DLL1550BAL Hotpoint Dryer - Instructions

opened back of dryer, located idler pully with broken bushing with plastic rubbing on metal rod making a loud rubbing noise when spinning. ordered part at 10:30 am and had parts by noon the next day, Christmas eve! wow!!!parts fit perfict, shiping time unbelievable, thanks to all !!!

I unplugged the dryer and moved it into a open spot on the floor.I then opened the door so I could release the top panel,and tilted it back.This allows the removal of the front of the unit. Folled the instuction for removing the drum and got it out. Cleaned up the area and removed the screws that held the drum to the bearing, and pulled the drum out. The instructions for removing the plate and the bearing where o.k., and the tips given for reassembly were helpful, but would have been easier to see if the were a seperate line. The parts fit GREAT, and this 1989 dryer is ready for a few more years.A good price on the parts and a quick ship.I will shop here again!

Unplug dryer and turn off gas to appliance. Remove small vent door front of dryer for access to burner assembly. Reach inside and remove all three wires attached to the valve. Using a backup wrench remove the union that attaches the 3/8" gas line to the burner assembly. Remove the two bracket screws holding the assembly. The entire burner assembly can now be pulled out. Replace the faulty igniter by spreading the retainer clip and inserting the new part. Use extreme care not to touch the new igniter with bare skin...best to use a helper to assist holding the assembly while you insert the igniter. Then replace everything as you found it . Soap all gas fittings, plug it in and enjoy your dryer.

place new filter in

Remove the Torx screws along the front top edge and flipped the top back. Removed two screws at the top inside holding the front panel on. Loosened two screws at the front bottom and took the front panel off. Pulled the drum out the front. I gave everything a good vacuuming with a shop vac and a long handle brush. Then went around back, removed the access panel, removed the rear drum bearing plate and installed the new one. Removed the rear bearing from the back of the drum and installed the new one (You have to work from both sides of the drum which makes it a little tricky.I used a couple of wire ties to hold everything in place while I lined everything up. Screws or punches would work too). The front drum slides are held in by 2 screws each and you could replace them without removing the drum. They need to be lubed with the lubricant supplied. I put the drum partially in then looped the belt over the narrow back part of the drum, around the motor pulley and idler pulley. Put the drum all the way in and the belt onto the drum by rotating it by hand. The belt ribs go against the drum. Installing the belt was the a little tricky but not impossible. It could be easier if you loosen the left side panel to give you some room to reach in but I was able to do it without doing that. Threw the front and top back on and was done. Total time was about 1.5 hours a lot of which was spent getting the dryer in and out of the little cubby hole it lives it.

I was disappointed that there were No Instructions included with the part. So I found a you-tube video that wlked me through it...Took off back of dryer, then the top, then the front to get to the igniter...could not pull out the part, so I had to reach in and replace it while it was in the dryer. It Works!

Make sure your power is off, When loosened the top and tilted back, the first thing I saw was the door switch, I guess I was just lucky I disconnected the two wires and checked it and it was bad. Got my new one from you and installed it. It has a ground terminal, which my model switch only had the two terminals. It working fine.I took the bad switch apart and the one leg on the copper U shaped contact had broken off. The Belt I have as a spare.

PartSelect already has a good video explaining how to replace the bearing. The only thing that I would have liked information on is whether or not to add grease. It did not appear, on any of the PartSelect videos, that any grease was added. I read where some people recommended lithium or other types of high temperature grease. I knew better than to use automotive/petroleum based grease. I elected to use a small amount of lithium grease. Addressing whether or not to use grease would be a nice addition to your video.

no instructions necessary for this part install