DLB6850BCL Hotpoint Dryer - Instructions

I called customer Servioce and they helped me with the corrfect part number

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

place inside of dryer

Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1

unknown
25 year old GE dryer started making strange scraping noises when running. This even when there were  no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.  

Kevin J. Reynolds.

Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.

First of all unplug the dryer, move it to a location that you have room to work around it. Remove the top and then take the two screws out that are on the inside of the dryer close to the top and then loosen the two bottom front screws only. Remove the front of the dryer and then look in the back of the dryer in the center of it and there is a square hole with a cover, remove the cover and behind it is a c-clamp, remove it. At this time release the tension on the dryer's belt and then pull the drum out towards the front of the dryer. Once this is done you'll be able to see the heater coils. You have to remove the bolts that the wires are attached to and cut the wire so you can pull the old coils through the glass rings to get the old coil out. Open your package and have a 48" yardstick or a tape measure and stretch the coils to the lengths in the instructions. Thread the new coils through the glass holders and then you have to remove the three heater wires that go through the wall of the ring so you can connect the new wires to the new bolts provided with your kit. One idea is to take a picture with your smart phone before you take anything off if it seems you can't remember what when where so you can see how the wires and bolts go back together. Once you have the bolts and wires connected you just reverse the process and put the dryer back together. *********** If I knew what I know now I would order a few of the glass holders because two of mine were burnt and I would have replaced them if I had them; I'd buy 4 to 6 of them to make sure I had enough.

Used online instructions. Worked well.

I got to supervise - my son did it for me!!!! Went very well!

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

I removed the screws holding the top on and screws holding the front panel and rear access panel. I then removed the 3 screws holding the drum. I proceeded to take the belt off then lift the drum out. I replaced the heater coil and then the slides. I reassembled the dryer and dried the towels that were in the washer. I saved $20 by ordering from Part Select and not going through the local repair store, not to mention how much they would have charged to do what I did. I’m not a pro at fixing things but can hold my own. Thanks Part Select I will order again from you if I need a part!

Removed the screws that hold the draying unit (barrel) to get accest to the back of the switch, and that's when I noticed that I will need the belt and I ordered to when my existing belt goes I have a replacement.

I looked on the internet for instructions to take the dryer apart,took the parts out one at a time ,and replaced them.It was easy and it made the dryer quiet again.I could see the obvious wear on the parts.I was happy to save the money a new dryer would cost.

open the front of the dryer, open the back access panel, remove the old belt fragment, pull front cover away from bushing surface at the front of drum, drape new belt around the face of drum, match location visible as the track of old belt, reroute belt at the motor and install tensioner in the proper way, reattach front cover, install back panel, done.

First I checked on-line "how to change a dryer belt" and followed the instructions. Remove front panel and slide belt over drum, in the back, put belt around pulley and hand trun the drum. on-line instructions had pictures to ensure proper install. It was easy.