DLB2450BDL Hotpoint Dryer - Instructions

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw driver.

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

The same procedures as posted in the video, but as applied to the model. Belt had broken. Bearing and front supports were worn, but the cause of the noise was a worn tensioner pulley bearing/arm, causing damage to the belt until breakage. Save the time and effort of a second repair and purchase a tensioner arm/pulley anytime the belt breaks as this is likely the cause of the original breakage. The hardest part on this older GE was getting under the drum to engage the tensioner and belt to the motor, as clearances we very tight. Review the diagrams, watch the video, and enjoy a quiet and well running machine for your efforts. PartsSelect is the only place to shop for appliance parts, my hat's off to excellent service, fair pricing and fast shipment. Thanks PartSelect!

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

I unplugged the dryer and moved it into a open spot on the floor.I then opened the door so I could release the top panel,and tilted it back.This allows the removal of the front of the unit. Folled the instuction for removing the drum and got it out. Cleaned up the area and removed the screws that held the drum to the bearing, and pulled the drum out. The instructions for removing the plate and the bearing where o.k., and the tips given for reassembly were helpful, but would have been easier to see if the were a seperate line. The parts fit GREAT, and this 1989 dryer is ready for a few more years.A good price on the parts and a quick ship.I will shop here again!

remove two bolts in back on the top two corners. four tiny screws right inside the door. the top comes off with the wires still attached. looking down from the back on the left side of the dryer there is the high limit thermostat two wires and two tiny bolts and it is out; it is very tight. The thermostat- limit 145-15 is located in the lint trap. top is off looking down the front of the dryer there are two bolts remove those pull up on the whole front move it off to the side open door remove the ring by tiny screws and lint trap. you can see the nose of the thermostat remove three screws that is holding a metal cover on and thermostat in place. Remember don`t lose a little metal clip for one of the screws it is tight space. Put everything back together and your done

place new filter in

Remove the Torx screws along the front top edge and flipped the top back. Removed two screws at the top inside holding the front panel on. Loosened two screws at the front bottom and took the front panel off. Pulled the drum out the front. I gave everything a good vacuuming with a shop vac and a long handle brush. Then went around back, removed the access panel, removed the rear drum bearing plate and installed the new one. Removed the rear bearing from the back of the drum and installed the new one (You have to work from both sides of the drum which makes it a little tricky.I used a couple of wire ties to hold everything in place while I lined everything up. Screws or punches would work too). The front drum slides are held in by 2 screws each and you could replace them without removing the drum. They need to be lubed with the lubricant supplied. I put the drum partially in then looped the belt over the narrow back part of the drum, around the motor pulley and idler pulley. Put the drum all the way in and the belt onto the drum by rotating it by hand. The belt ribs go against the drum. Installing the belt was the a little tricky but not impossible. It could be easier if you loosen the left side panel to give you some room to reach in but I was able to do it without doing that. Threw the front and top back on and was done. Total time was about 1.5 hours a lot of which was spent getting the dryer in and out of the little cubby hole it lives it.

Make sure your power is off, When loosened the top and tilted back, the first thing I saw was the door switch, I guess I was just lucky I disconnected the two wires and checked it and it was bad. Got my new one from you and installed it. It has a ground terminal, which my model switch only had the two terminals. It working fine.I took the bad switch apart and the one leg on the copper U shaped contact had broken off. The Belt I have as a spare.

PartSelect already has a good video explaining how to replace the bearing. The only thing that I would have liked information on is whether or not to add grease. It did not appear, on any of the PartSelect videos, that any grease was added. I read where some people recommended lithium or other types of high temperature grease. I knew better than to use automotive/petroleum based grease. I elected to use a small amount of lithium grease. Addressing whether or not to use grease would be a nice addition to your video.

no instructions necessary for this part install