DE21CA Maytag Dryer - Instructions

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

actually used the videos available on your website and it made the job really simple other than the fact that I live in Florida and it was 96 degrees and my dryer is in my non-air conditioned garage.

Tip: If the belt broke make sure the Drum Rollers are not seized which could have broken the belt. I recommend if replacing the belt replace the Drum Rollers (2- required) at the same time.
The instruction sheet that came with the Drum Roller kit is straight forward. It provided detail on what to disassemble to replace the rollers. So follow the instructions. Tip: Make sure you have a C – clip ring pliers to remove the C clip. The instruction sheet calls it the snap ring
The Idler Pulley came with no instructions, however it was easy to replace. The idler pulley is secured with an “E” shape clip which can be removed with a small straight blade screw driver.
The instruction sheet on how to install the belt was good showing how the belt is routed. The instruction wants the belt installed from the front around the tumbler then from underneath the tumbler towards the back and around the motor pulley and idler pulley. It is hard to see the motor and idler pulleys from underneath the tumbler. However I think it was easier if the tumbler was moved forward enough so you can see the motor and idler pulleys from the top. Install the belt as shown in the instruction sheet diagram around the motor pulley with the groves of the belt are against the pulley, then around the idler pulley. While holding the belt with slight tension, move the tumbler back into position while routing the belt around the tumbler and slowly turning the tumbler until the belt is completely installed. The belt should be about 1-1/2” from the back screws which hold the tumbler baffles. Note: the belt should be installed with the flat side against the tumbler. The belt should not be in the back grove of the tumbler.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

Remove the two screws that hold the front cover. Remove front cover and disconneted wiring to door switch.Remove the cover ( lower right hand corner )back of the dryer to gain access to belt idler pulley/tensioner. Remove old belt and slide new belt on the tumbler.

First I unplugged the dryer. Then, I took off the front cover, then a piece that holds the tumbler on. I put the new belt on and took a few minutes to make sure the belt was placed correctly. Lastly I put everything back on and plugged it back in. She started right up.

I happened to come across a repair story posted by Wayne From Minneapolis MN about how he reinstalled the tumbler, plugged the dryer in, and started it up but forgot the belt and realized that it was the blower wheel that was loose on the shaft. As soon as I read that, I said, "Yes! that's it!" So I ordered the blower wheel and a belt. I decided to replace the belt since I saw it was slightly frayed. After all, the dryer is almost 20 years old!

First, switched off the power to the dryer or disconnect it from the outlet. Took the front panel off by removing the two screws near the bottom of the dryer. Pulled the bottom of the panel out and the two clips on the top just disengaged easily. Be careful, there are two wires connected to this panel. Just rotated it to the left and let it rest vertically. If need be, the two wires can be removed easily.

Next, I removed the four screws to take out the front tumbler and the tumbler. Set them aside. Then I removed the belt. You might want to pay attention as to how the belt goes around the motor pulley and the idler pulley before removing the belt.

After nearly 20 years, I'm surprised that it wasn't full of lint and dust. Gave it a good vacuuming and clean up.

Next, I removed the blower cover, the retaining ring, the hub clip, and the blower wheel. Installed the new blower wheel, hub clip, and here's the challenging task without the proper tool - putting the retaining ring back on the shaft! It took me about 5 minutes to put it back on the shaft with a small flat-head screw driver and an awl. Reinstalled the blower cover.

Next, I put the new belt over the pulleys and loosely hung the belt on the back tumbler to hold it up. Then I put the tumbler back in and worked the belt over the tumbler. I let the belt sat in the groove of the tumbler first and then when the tumbler was in position, I worked the belt over the two pulleys in to the proper position. Then I moved the belt to strap over the top of the tumbler. At this point, I just rolled the tumbler with my hand when part of the belt was out of the groove and on top of the tumbler. The motion took care of getting the rest of the belt out of the groove and on top of the tumbler as it should be located. Reinstalled the front tumbler and then the front panel.

Powered it back up and started the dryer and viola! the rumbling noise was not to be heard. Just like it used to sound - a low humming noise. Thanks Partselect.com for the helpful repair stories and the speed in getting the parts to me.

I bought this machine in 1984. For the belt to last this long, is extraordinary. The belt comes in a plastic bag with instructions. After removing the front cover(2 screws at the bottom, tip bottom out towards you. Cover unhinges from the top. Lean face against a wall. Don't remove any wires). I then vacuumed the inside thoroughly. Used a parts brush to wipe everything off, and blew out with compressed air. Vacuumed again. A bit obsessive, but gas and dust are not a good combination. So why not take the extra time. There is a continuous mark on the circumference of the drum, left by the original belt. Use this as your guide to locate the new belt. Rotate the drum by hand to make sure it tracks correctly. I also ran the motor with everything open, to make sure everything was cool before I buttoned it up. Also took the time to replace the gas line with a new one, and duct-taped the vent pipe to improve air flow.

Unplug dryer
Remove front (2 screws at bottom)
From bottom lift out and up to release top bracket
Move front panel gently to the left not disturbing wires
Remove blower cover with nut driver
Remove expansion clip on shaft with expansion clip pliers
Remove blower clamp with pliers
Slide blower wheel off
Replace blower wheel an reassemble

Fast receipt of parts from supplier . All parts went together very quickly. Don/t recommend this work for those who have no mechanical skills. realignment of screws can be very tricky . They must all be correctly aligned first and driven in at diagonals to equalize pressure . Job needs to be used with hand tools as it is easy to strip out the threads in dryer by overtightening the screws.
PS before this we had replaced the drum belt.
Update:
We ran the dryer after replacing the drum support rollers and the idler pulley and it was smooth for about 5 minutes. then the rumbling and uneven rotation started up again! The tip-off was when we had done a test roll on the drum after changing the above parts, we heard a rumble from the blower wheel! so we ordered the blower wheel, replaced it and the dryer sounds like new.
Thanks to others who have written their stories which helped us figure out the problem. : ) saves big $$ on buying a new dryer. PS ours is 15 years old and has had heavy use.

I took out the old worn out part and replaced with the one I order.

Problem was the blower wheel, (Plastic deteriorated). Replaced the tumbler and motor belt as well as th idler pulley. While the blower wheel turned out to be the problem, the other parts were significantly deteriorated. Since I had the dryer disassembled it made sense to replace the other parts. The 24 year old dryer runs like new. The parts select instructional videos were extremely helpful.

From the sound it made I thought it was the rear rollers. That happened once before on another dryer.
After removing all the parts I foung out they were fine.
First unplug the dryer:
Then remove the dryer front door panel.
2 screws at the bottom of the door.
Lift cover from the bottom of the door, it is kind of on a top hinge.
On the bottom left hand corner you will see the plastic cover for the blower. It has 6 small screws that hold the cover on.
Once the cover is off you will see the blower wheel.
Use a pair of Snap Ring Pliers to remove snap ring at end of the shaft.
Use a pair of needle nose pliers to remove the clamp around the blower wheel that holds it onto the shaft.
Slip off the old part.
That was the rumbling noise.

Pulled the power plug,removed the front cover,disconnected the door switch ,then the drum cover then the drum giving me access to the drum rollers and the belt,replaced the rollers [applying grease the new ones] and belt as I reassembled the drum and drum cover,then the front cover went to the rear access cover ran the belt over the tensioner pulley abd motor,plugged the dryer power cord in and tested