CTX21EKJR Hotpoint Refrigerator - Instructions

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.

Put two new end caps on the bar and then snapped the whole unit onto the door. Took longer to get the parts out of the mailing envelope then it took to repair the shelf.

First of all, finding the part was very quick and easy, which really surprised me. The repair itself took only a few minutes. Just removed the two screws holding the broken end cap, and screwed the new one back in place.

Took old gasket off put new on.

Gasket came well packaged so only ran hot water over it briefly and put it on.

Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.

I watched videos of the modern refrigerators and figured out how to do my model by taking my time watching as many videos that pertain to my refrigerator I finally I expose the evaporator I noticed that the defrost heater was buckled up and totally disintegrated and slowly took my time looking at the screws I took it out and I didn't have to do
disassemble bottom of the freezer to replace the part, you definitely had to have common sense and to be mechanically inclined to do this repair otherwise it was easy

Took out the light sockets, plugged in the new ones. I found the manual on line to find the part numbers. Parts select parts were perfect

Placed new gasket into dryer,( recommended by 2 u tubes) high heat for about 10 minutes and was a snap getting softened gasket into little tiny slot actual placement was done twice as there was a twist in the seal i missed the first time so did do twice but was so easy this way was almost sad thinking it would have been 100$ deductible having someone do it and who knows what normal cost would have been......thanks u tube

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.