CSX27DLR Hotpoint Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
would not "dump" ice cubes
I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.
Parts Used:
-
Phayo from Lake Charles, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
summer cottage lost heat during winter inlet valve for icemaker froze
parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>
Parts Used:
-
Robert from Waterford, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
bad fan motor
-
theodore from salisbury, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker leeking
-
Wes from Marion, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Both cams (upper and lower) broken
The part came within 3 days. But it was only one cam. Part was described assembly so i thought it had both cams. I ordered the upper cam which attached to the door bottom. When I matched the new to the old --they were different. They looked the same until you put them side by side. Being the mechanic I am, I cut the rivet holding the assembly cam and pop riveted it to the old assembly. It was not difficult but annoying as I had the correct model (I have the original use and care guide book). I must commend PartSelect for their promptness.
Parts Used:
-
Louis from Cortland, NY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Put the part in and observed water leaking from the ice maker which caused the cup to break
Ordered new Ice Maker from you and fixed the problem completely.
Parts Used:
-
John from Ravenden, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no ice
-
Richard from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Not dispensing water
I watched the video on the partselect website once and completed the repair. Very easy!
Parts Used:
-
Anthony from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Parts Used:
-
Charles from Spring, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker was spewing water into freezer
Ordered this part after i replaced the plastic tubes on the back as the problem persisted. loosen the nuts holding the water inlet lines, remove the cover to the valve. remove the valve and the water inlet line to the the valve. Disconnect the 2 outlets from the valve. 1 outlet to icemaker and other outlet to water cooler (bigger). Connect water inlet and 2 outlets to the new valve, test the water lines. Found the inlet is leaking, removed it and added teflon tape and reconnect it. All is done. Then I left the freezer door open for 3 hours to melt the ice on the wrong places and all is well.
Parts Used:
-
andy from clearwater, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!