CSX22KAXAAD Hotpoint Refrigerator - Instructions

The refrigerator was no longer cooling and it was suggested by my father that it could be our defrost timer as he has owned many Hotpoint refrigerators in his lifetime and he said the defrost timer was always the problem he had with them when they were not cooling properly. I removed the cover and unplugged the defrost timer, ordered a new timer through this website and installed it by plugging it where the old timer was, replaced the cover and plugged the refrigerator back in. The refrigerator is now cooling again and just in time for Christmas.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

quick and very easy to enstall

Removed guard at bottomof frig. Located timer & performed tests. Manually rotated timer motor until defrost cycle start. Watched timer for several hours. Timer did not come out of defrost.. Rotated timer more until compressor started. Cooled fine several days then started to get warm again. Manually defrosted and started compressor again. Ordered part. Followed wiring diagram on timer for push on lugs. Frig now back to normal operation.

First I removed the two screws that held the old slide to the refer side wall, (after unloading the shelf and taking out the Veg. draw). I then put the screws in the new slide spots and screwed them into the refer wall using a hand screwdriver (phillips) and put everything back in place. It was about as simple a repair of anything I have had in the past 75 years. I didn't even have to swear.

I knew that the compressor was cooling because the freezer was half-working. The back wall was frozen-up and found that the iced-up coils where blocking the air circulation. So even if the fan was running, there was no air circulation. Hence the deforst cycle was not working.

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door then lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.

This was so easy! I got the part number off of the broken part, ordered online, and it was delivered the next day!!! So fast! Then I just unscrewed the broken part and reused the existing screws to install the new one. It took about 5 min.

Thanks for making everything so fast and easy!

First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.