CSC22GRAAD Hotpoint Refrigerator - Instructions

I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !

disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .

took out 4 screws - lowered timer cover - replaced timer- put it back together

I supported door with 2* 6 scrap wood. I used cedar shingles to raise door to correct height.
Using a socket wrench, I removed the hinge from the fridge and the cam assembly from the door.
I installed the new hinge and cam using the shims thatwere behind the original parts.
I removed the 2*6 supports and the door now works perfectly.

Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove from hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

This repair replaced two riser cams - one attached to the bottom fridge hinge and one attached to the bottom of the door. The two cams
mate together. So, don't just buy one cam, buy two.
1. Removed all contents off the inside of the door as well as the bins.
2. Unscrewed single screw holding plastic cover over top hinge.
3. Unscrewed 2 screws holding top hinge to the top of the door and removed the top hinge.
4. Pulled door up and off bottom hinge and layed
on floor.
5. Removed plastic grill on bottom of fridge.
6. Removed 2 screws holding bottom hinge in place.
7. Using a vice to hold the hinge, I used a hacksw to cut through the rivet holding the riser cam to the hinge plate.
8. Used a small bolt & nut to secure the new riser cam to the hinge plate.
9. Reattached hinge plate to the bottom of the fridge.
10. On bottom of the door remove two screws holding riser cam to door.
11. Position new riser cam in place and reattach to bottom of door.
NOTE: on my door, the metal SHIM that goes between the cam riser & door was also broken. I ordered the replacement SHIM but it turned out to be made of PAPER. So, I didn't bother putting it on. If the riser cam wears out again, I'll just replace it again.
12. Put door back on and secure the top hinge to the top of the fridge and you're done.

Was able to pull the door up to the normal position, then blocked in place with 2 2x4's. Easily removed the hinge assemble and the door closing cam, which had broken in two.
bolted on the replacement parts in 10 mionutes and the door was a good as new: peice of cake!!!

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

Turn of power to fridge. Removed all shelving in freezer section. Unscrewed back panel from freezer area. Removed old defrost term t-stat from top of evaporator coil assembly. Cut existing two wire leads, spliced in new T stat wires. sealed wire splices from water egress and clipped new t-stat in same position as old one. Reassembled rear panel, installed shelves. Turned power back on.That's it.

I removed all items from area of refrigerator. I removed the drawers. I unscrewed the broken slide rail. Upper drawer had left side broken. Lower drawer had right side broken. I simply screwed the new slide rail in. The glass shelf didn't fit, so I took a pair of needle nose pliers and broke off a tiny piece on the slide rail that was preventing the glass from dropping in. (I checked the old one first and could see the same thing had been done) I screwed each rail in and dropped the glass shelf back in. (The lower shelf was broken and I ordered a replacement at the same time as the broken rails. I put the glass into the plastic holder of the old (broken) shelf and slipped it back in. Very easy. I'm a housewife not a repairman. I saved a few dollars on a house call.

Removed the top hinge and the door.
Removed door stop held in place by 2 screws, installed new door stop.
re-installed door and top hinge.
Easy once the correct diagnosis was made
It would have been nice if I could have e-mailed you the symptoms and received an accurate diagnosis. As it developed, I initially replaced the door cam before realizing that the door stop itself had broken.