CFEH272ITD1 Refrigerator - Instructions
Parts
Symptoms
Videos
Instructions
All Instructions for the CFEH272ITD1
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Parts Used:
Michael from FREE SOIL, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
1 person
found this instruction helpful.
Thank you for voting!
Ice maker had stopped crushing ice although it still made cubed ice.
Took out the old ice container assemblyr and put in the new one. No installation was required. Just replaced it in the ice maker housing.
Parts Used:
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.
Simple tightening of the screw with the right tool.
Parts Used:
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
Gasket was torn and leaking cold air causing condensation and water dripping when door was opened.
I pulled the old one out and pushed the new one in place.
Parts Used:
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 person
found this instruction helpful.
Thank you for voting!
The fridge icemaker would pit out crushed ice. No whole cubes
I had to remove everything inside including the surrounding box and disconnect all the wire connector s. The solenoid that was bad was behind the cover that the auger motor cover. . Job was easy after I determined I had to remove everything that was not attached to the back wall.
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
1 person
found this instruction helpful.
Thank you for voting!
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again. The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Parts Used:
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
1 of 2 people
found this instruction helpful.
Thank you for voting!
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out (only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
3 of 8 people
found this instruction helpful.
Thank you for voting!
We had a broken bin on one of the doors.
We just slide in the bin.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 people
found this instruction helpful.
Thank you for voting!
No water to the ice maker or water tap.
Removed valve unplugged valve from electric removed water lines from valve and then reverse procedures then turn on water and use.That was it.
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
2 of 5 people
found this instruction helpful.
Thank you for voting!
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
2 of 5 people
found this instruction helpful.
Thank you for voting!
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Parts Used:
Nancy from LEHIGH ACRES, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)
2 of 5 people
found this instruction helpful.
Thank you for voting!
very Simple!
Insert the bottom part of the trim first, then pull up to snap on the top. PartSelect.com is a fantastic website!!
Parts Used:
Lorraine from Arlington, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 people
found this instruction helpful.
Thank you for voting!
clear door bins cracked
slid shelf out, slid new bin in.1 2 3
Parts Used:
Therese from Homer Glen, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 3 people
found this instruction helpful.
Thank you for voting!
No problem - just replace every 6 months!
Just place new filter and lock it!
Parts Used:
BO from SUN CITY WEST, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 of 3 people
found this instruction helpful.
Thank you for voting!
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
0 of 1 people
found this instruction helpful.
Thank you for voting!
All Instructions for the CFEH272ITD1