CFEF3017USA Frigidaire Range - Instructions

Replaced infinite control very easily.

I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be

NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.

Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

Unscrew the 2 screws at the back of the oven bottom pan in the range. Place new oven pan in and rescrew the 2 screws. I could not get the two screws screwed back in. Since the bottom pan cannot move from its position, I felt like the two screws were not necessary.

Easy watched on line video

Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.

First, make sure power is off to range. Removed backing cover, pulled one wire off infinite switch at a time to put in right place on new switch. Easy fix.

Removed the defective part. Install the new part, insert the connectors. Now its working

Slid stove out, disconnect power plug, removed top control panel with 4 screws. Unplugged two electrical connectors. removed knob and nut removing switch. Re-assembled in reverse order and test all functions.