CAV2005AWW Magic Chef Washer - Instructions

Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.

Unplugged everything, disconnected hoses, took belt off and put new one on.

Easy to remove broken part. Found rust, so after cleaning I applied paint (I let dry overnight).

By manipulating the washer drum, moving left and right, the screws were easy to get to. However, to get the screws back in took tightening by strong hands. Plus, found that the lid sensor had worn out, so that was adjusted.

New screws would probably make the job easier.

All is fantastic and I found it was "easy" to replace with finishing help from strong hands.

took drum out replase snubber put drum back in

First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a kitten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3

Remove two screws holding a special clip on the back of the washing machine (near top- one on each side). Top of washing machine pops off now by prying front edge up (2 snap type clips hold front edge of top down). Once top is loose just pivot it up on edge so you can get to the bottom side of it (don't have to remove the wires etc. as they are long enough for this). Remove one screw in each hinge half located on bottom side of washing machine top and remove old hinge half from top. Remove broken hinge halves from door to washing machine by removing one screw from each one. Put new hinge halves together and fasten to door. Then set entire hinge/door assembly on washing machine top and screw to top as an assembly. Snap top of washing machine back down on front of machine and put clips/screws back in on back of machine.

replaced water pump and belt ,had to shim motor mounts , working pretty good , but still needs some tweaking

I popped the clips on both sides of the top with the putty knife. Raised the lid. Unscrewed the one screw on the old hinge. Screwed on the new.

It took a PhD in hinge replacement to do this.

I had to pop the top of the washer which is hinged in back. Raised it up and removed old hinges. replaced "hinges and hinge pins. It works like new.
Thanks for your "website". It was very easy finding the parts I needed.
Sincerely
Bill Hines

Once the machine was unplugged, I used the paint scraper to release the top of the washer by inserting it at right front and left front about two inches from the sides. The spring clip's were released and the top swung back on the rear clips . The lid hinges were exposed , removed and replaced with the the screws from the original parts, "as they do not" come with the replacement parts.
"Replacing first one side" then taking the lid and replacing the parts (pivot parts) attaching the- 2nd lid hinge piece at this time as they will not go together in any other fashion. Snap thewasher top down to close. I would suggest spraying a little silicon spray occaisonally, to avoid the parts failing prematureily. All told about 20 min. to do the job. Don't forget to plug in the washer!

Removed the screws and lid. Cleaned up lid and parts. Had to sand down pin as to tight on lid. Easy job.

Followed instructions and needed help lifting drum out but no problems. Parts fit perfect and unit is as smooth as new.

Viewing the video on how to replace the hinge pin was very helpful orienting me on how to get the job done. As I viewed the video, I thought to myself, "It couldn't be that easy!" Once I received the part in the mail, which was received quickly, I followed the video instructions in finished the repair in 5 minutes. It was a great experience and gave me a new online parts distributor that I will use in the future since I am a born "Do it Yourselfer." Thanks.

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.