Models > C202 > Instructions

C202 Jenn-Air Cooktop - Instructions

All Instructions for the C202
196 - 210 of 228
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner on stove didnt work
It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...
Parts Used:
Delta Frame Surface Unit - 8 Inch Surface Burner Receptacle Kit
  • Timothy from Greybull, WY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken switch
Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.
Parts Used:
Infinite Switch
  • Robert from Coral Springs, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
broken surface burner knob
Pulled off the knobs,replaced switch, put on the new knobs. Your web site is easy to use, and your parts are first quality. Dave
Parts Used:
Infinite Switch Surface Burner Knob Kit
  • dave from williston, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
heating coils would not work
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Parts Used:
Surface Burner Receptacle Kit
  • Adam from Kempner, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
needed drip pans for burner
easy, drop in
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • Arva from Horsecape, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Switch post broke. Could no longer turn that burner on.
Replacing the switch was quick and easy. It actually took only about two minutes.
Parts Used:
Surface Unit Infinite Switch Kit
  • Joe from Cottage Grove, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The original filter was decomposing each time I washed it
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.
Parts Used:
Grease Filter
  • Sharon from Kenai, AK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
surface burner stopped working. Was not heating up.
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Parts Used:
Surface Burner Receptacle Kit
  • timothy from south bend, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
stem on burner controls broken
follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.
Parts Used:
Surface Burner Knob Surface Unit Infinite Switch Kit
  • Kenneth from Greenwood, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
bearing went out in blower motor
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Parts Used:
Blower Motor Exhaust Vent Blower Wheel
  • richard from white castle, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
New drip pans and new element
Set in drip and and plugged in element.
Parts Used:
Delta Frame Surface Unit - 8 Inch Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • Dorothy from Gurley, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner did not heat
New receptacle element. I am a girl and I did it.!!!!
Parts Used:
Surface Burner Receptacle Kit
  • lula from Antelope, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burned out surface element
I pulled the old one out and installed the new one. Never broke a sweat.
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • Blair from Edmonds, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
failed heating element
Took out of package and plugged in. turned on. It took 5 minutes.
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • James from Tigard, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The burner switch was broken
The repair was easy. First, I turned off cooktop circuit breaker. Then, removed the burner switch panel and the nut securing burner switch to panel. Disconnected the wiring and refit with new switch. Install switch panel and turned power back on. Now it's time to cook some dinner. Let's eat. :)
Parts Used:
Infinite Switch
  • Michael from Shrub Oak, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the C202
196 - 210 of 228
Back to Top