C201 Jenn-Air Cooktop - Instructions

No tools were required to replace the drip bowls and knobs. I was really impressed with the speed of delivery. I ordered the parts one afternoon,and they were on my doorstep the following morning!

I unplugged the old ones and put in the new ones.

Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.

Placed new burner knobs onto cooktop. easy

I just lined up the parts and put them in the burner. After a year of spending money and many hours, trying to get wrong parts to work and trying to get something that fit and didn't leave gaps, I got parts that really fit and work and were exactly like the parts they replaced! The woman I spoke to was very helpful and helped me to order the right drip pan! I got the parts very quickly and was very pleased with the woman that helped me with my order. My Jenn-Aire works and finally heats perfectly now and I am very pleased! Thank you everyone!

After a long time being without a working stovetop-an electrician friend said we needed to change a switch-it was ordered and came very quickly and installed-then it was determined that we needed a switch for the other side of the stovetop-I ordered it and got it the next day! It was a joy cooking thanksgiving dinner on a stove that worked-and I have a new friend that is interested in seeing me on a more regular basis. I know if I needed any kind of parts, I would check with partselect first ;)

I used the blow torch to heat up a small screwdriver till it was red hot. I then quickly applied it to the inside of the new knobs to make the shape more accommodating to the stems size. Once I thought I had about the right size, I heated the screwdriver again and melted the inside of the knob again and quickly pressed the know on to the stem and molded the inside as best I could to the stem.So far so good. Everything is working again.

Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...

The Jenn-Air R201 is a stand-alone Range with 4 burners, 2 6" and 2 8". Two of the burners were out, one was simply electrically open, the others were badly worn. One of the switches was bad and 2 of the burner connectors were bad. I started by opening the breaker for the range at the breaker panel, and removed and discarded all the burners. The ring adapters were rusted on all 4 burners as well as the trim rings. All 8 of those were removed and discarded. The broken receptacles were replaced using the high temperature wire nuts. Caution: make sure the high temp wires are tightly wound together with pliers before putting on the high temp wire nuts. You must have a good mechanical connection before the wire nuts go on. Replacing the Infinite switch for one of the burners was frought with problems, since the push on connector at one of the terminals broke. I had to replace the push-on terminal and purchase a good quality crimp tool. Once that was done, I replaced the trim rings, drip bowls and put the new burners into their respective connectors. Hint: make sure that the indicator lenses are not cracked, or the indicators will not be held in place and can float inside the control unit and possibly short out. If they are damaged, replace the lenses. After checking all connections, the control unit was re-installed, and the range circuit breaker closed. The unit worked perfectly afterwards and looks like a brand new unit - only about 23 years old. One of the original infinite switches is now acting up, so that will need to be replaced soon. Thanks for having these parts, I saved a lot of money rebuilding this range!!

Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.

Pulled off the knobs,replaced switch, put on the new knobs. Your web site is easy to use, and your parts are first quality. Dave