Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
had squilling noise.clothes get stuck in between top of drum and dryer
inside dryer door housing i removed two screws these hold top of dreyer on.pulled dryer top up and it unhooks from control panel.theres two more screws inside the front door asembly located at the top on booth sides.remove them and the front is free except for dryer door switch.lean it back far enough to unpug wires.lay door asembly on the floor.drum slide pops out with screw driver at the top the bottom just slides out.drum bearigs are plastic strips on the drum slide. pull the old ones out if their is any left.replace with new.you need four drum bearings.then put back together the ame as you took it apart. good luck terry
loud squeaking, and clothes hanging on the plastic
open door, remove two screws from below the top. gently remove the top from the side and bottom panels. remove two 5/16 screws from front panel hold panel so it does not fall. the bearing assembly will come out by moving the bearing towards the dryer, and pulling upwards. replace with new bearing, use 4 front dryer slides and reinstall the top and front panel. can be done in less than 15 minutes
Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.
My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.
1. Before we started anything we unplugged the dryer and disconnected the vent. 2. We removed the top and loosened the contol panel on top. 3. We removed the front. Be careful of the wires. You can label them, or just remember where they go. 4. Lay the dryer down on it's back. This make's it easier to remove the drum. 5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it. 6. Once the drum was removed, we removed the screws from the inside of the drum. 7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description) 8. We screwed in the new "top" and put the dryer back together.
Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.
Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.
Dryer started making screeching noises while running, got progressively worse. Without taking it apart first, I ordered a front drum bearing and slides because this site said it fixed the problem the majority of the time. The site said replace the slides in pairs, but there are actually four. I picked up 2 more at a local appliance store, at roughly twice the price. Turned out I didn't need th replace the plastic piece called drum bearing, just the 4 slides that clip onto it. It is really easy to get the top and front off with just a phillips screwdriver. I did not check the rear center main bearing, as it requred removing the drum. The squealing lessended but it still was bad. Took it back apart and pulled the drum, and fount the rear main bearing bad. I found one at the same local store for only 2 bucks more than on this site. This was a bit more of a hassle, you really need two people to get it mounted to the drum. Tip-pre thread the holes with the self tapping screws, it makes it easier to get it together. There was a bit of lint build up under the drum heating element cover, so it was good to clean that out. Also blew all the dirt out of the motor with compressed air and shop vac. There was a access panel on back to get to the motor and belt tensioner. Got the dryer all buttoned up and now it runs nice and quiet.
i read in the forums about what was wrong and ordered the parts--they really need to tell you there are four bearing slides to be replaced-- you have to order singly. other than that - my grandson could repair it and the silence really is golden Moose
I followed the directions from the other d-i-y'ers at partselect.com.... removing 2 screws inside the door opening that allow you to remove the cabinet top. Next, removed the 2 screw on the inside cabinet frame that allow the front of the cabinet and door to lean out. I disconnected the wires, labelling them with tape. You just lift up the front and set it to the side. I then removed the back access panel, reached inside and pulled down on the tension bar to allow the drum-belt to come off the pulley. (It helps to remember or draw the path of the belt...I got a little confused when it was time to put it back on). Then me and my wife pulled the drum out towards the front - you have to spread the cabinet open a little - but you can do this without even having to remove the control panel (but if you remove the panel, it is a little easier). The rest is mostly just unscrewing screws.
The problem was definitely the rear drum bearing, which was rusted and the carbon/plastic sleeve was crumbled. I bought it and the front "drum bearing", but I didn't really need the front piece, I really just needed the plastic "slides", which I thought were attached to it, or would at least come with it, but didn't. I'll get those later.
The repair was definitely worth it. If you have a 10 yr old dryer, just clearing the lint and crud from the the blower ducts will make it more efficient - cutting our dying times by 30-50%. The duct beneath the lint filter was probably 60% blocked. No more squeaking. I only wish the little plastic slides weren't $7 a pop, and would come in a package of 2 or 4.
Had a repair shop quote 230 for repair . Spent 66 on parts and did the repair in 45 minutes using the instructions from folks on this site . Very happy with results thanks
Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.
- Removed two screws at top left and right of door. - Removed top dryer panel - Removed two screws holding front panel in place - Noticed drum slide was missing because front drum bearing was worn away and slide had fallen off. - Went ahead and removed drum to replace rear drum bearing (probably not needed; should have disassembled it first to discover this). Would have been better to pull drum first (loosen idler pulley and release belt, pull drum straight out) instead of attempting to unscrew bearing. Be sure to note how the idler pulley is set. - vacuumed tons of lint up - Replaced bearing (needed a second person for this; drum too big to reach around. be sure to pre-thread the bearing) - Ordered front drum bearing, waiting to repair it now, should be good after this.
