Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The left front tab holding Rack Adjuster to slide out rail snapped off
I did a Youtube search and discovered there were a couple that showed the replacement in detail. I watch the entire process once and then had my laptop beside the upper rack and paused the video after each step. That worked well
These wheel assembly that came on the lower rack of my dishwasher were junk! They started falling off within 6 months. I put them back on to the point that the pin in the center of the wheels would no long stay in place, thus the frustrating situation of the wheels falling off often.
Took minutes to repair. Unhooked the electrical plug connector to the drain pump. 1/4 turn to the left and pump was off. Just the opposite to install new pump
Take out the upper dishwasher rack. Place the adjuster towards the back of the upper each place attachment clips to secure adjuster and the adjuster clips to the back of the housing. Check to back sure adjuster move up and down and click back into place. Your installation is complete. Good luck!
Pulled out dishwasher, removed 4 bolts holding the track to the dishwasher, replaced track and installed the 4 bolts. Pushed back the dishwasher and works like new. The new tracks are riveted instead of spot weld and will last longer.
This was so simple! Some plastic tabs snapped off the upper rack adjuster in our dishwasher (which is not even 4 years old, so you can see how crappily made these things are), rendering the entire appliance unusable since the water sprayer thingie attaches to the underside of the upper rack. I was able to easily find replacement rack adjusters on PartSelect and thanks to the repair video, was able to install them in about 20 minutes. Most of that was rewinding the video since I had trouble getting the broken adjusters off! So delighted to have been able to do this myself and avoid paying $$$ for a repairman call out and replacement parts.
A plastic part on the top rack of my 2 year old dishwasher broke. Automatic dishwasher soap is corrosive and plastic parts should not be used in a dishwasher in the first place
The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free I was not happy with Part Select! Part Select cost me time and money and didnt get the job done
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Left-side rack adjuster broke, so upper rack couldn't be used properly.
Per suggestions from other reviews, I looked for You Tube videos for replacing this part. The video I used was completely necessary, but moved way too fast, so required lots of stopping, rewinding and starting again. But I managed to get the old rack adjuster removed and the new one installed without too much trouble. Then I tried installing it in the pull-out rail. The front connector on the new adjuster would not fit into the appropriate slot. Initially I thought maybe the part was defective, but determined that the dimensions were as accurate as my eye and tape measure could evaluate. Finally, I settled on the expedient of filing away at least 1/16" from one edge of the slot so that the connector would drop into place. Not sure why this discrepancy existed but the problem appears to be resolved.
Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!
This was tricky, not so much the difficulty of the repair so much as finding the right instructions. There weren’t any on your website. YouTube videos were all over the place in terms of specific set ups. Eventually I found the right one. This would have been very easy and would have taken less than 15 minutes if I had the right instructions from the start. Most of my time was taken with searching for instructions.
pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.
Dishwasher was leaking at the bottom edge of door.
Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.
