AYG2200AGW Maytag Dryer - Instructions

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

Very easy repair. Just needed to remove some screws to access the heating element area. The fuses are (1) just above the elements and (2) to the right side of them (if facing from the front). Alittle loosening with a philips screwdriver, removing blown fuses, replace with new fuses, tighten new fuses in place, replace outer screws and job done. Also made sure to fully clean lint collection area. I had a good amount stuck in there and it restricted air flow which caused the fuses to blow. It took 6 years worth of drying to make it happen.

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

First, I inserted a screwdriver between the front panel and the top and popped the top loose. Next, there is a screw close to the top of the front panel on each side. Remove these. Next I unplugged the light switch from the front panel and removed the panel. Next, unscrew the gas line from the burner assy. and remove the screw holding the burner assy. to the frame. CAREFULLY, remove the burner assy. taking care not to break the ceramic igniter. Remove the assembly and unscrew the brass screw on the right side of the burner. Replace the screw with the new assembly furnished with the conversion kit. Remove the tube that directs the gas to the ducting. Unscrew the orifice fitting and replace with the new fittings furnished with the kit. Reinstall the tube and CAREFULLY return the burner assembly to the dryer. Screw the assy to the frame and re-connect the gas line. Replace the front panel, 2 screws, and snap the top back down onto the front panel, taking care to align the two guide pins. Connect the gas line to the dryer and install the ducting. Plug it in and test for leaks.

The top was hard to figure out but I found that it pops off at the front with a flat screw driver. Be careful not to scratch the paint. I found that a rear drum roller was bad and the drum seals were deteriorated. I ordered a new belt, roller kit, front, and rear seals. This way I hoped I will not have to take it apart again. The seal were the hardest parts to replace. Make sure you look and remember how they were on before removing them. The directions were not to clear on the seals. The rest were good. It is much better to do it once. Take a picture if possible, it might come in handy as I took mine apart a week or so before the parts came in. I also cleaned out all of the accumulated lint buildup with a shop-vac, including the vent pipe, heater area, and front door. When I was done with this it worked like brand new.

My wife's dryer started squeaking very high pitched, intermittently and then continuously when running. It progressed to a loud shrieking, unbearable throughout the house. Make sure you unplug the dryer. First I replaced the Drum glide and cushion kit. This was easy to do. Pry open the top of the dryer open with a screwdrive or putty knife. Now reach in and remove the retaining screws holding the front panel against the side panels. After releasing the front panel, let it fall forward about 4 inches and then unplug the two wire connected to the door closed sensor. Now carefully slide the thin belt towards the back of the dryer, it will release eventually as it is pulled off the pulley (dont worry, getting it back on is not that hard). Now you can remove the drum. After removing the drum, there are two tan or bluse plastic drum glides that the fron of the drum rests on. They can be worn out along with the cushion beneath them. Replace them with new one. This actually did NOT fix the problem. I put everything back together and....SQUEAK!! Next I undid everything as before and removed the drum. Now I decided to lubricate the rear rollers. First I used a silicone lubricant that again did not fix the problem. I could not find hi-temp lubricant, so I decided to use Axle grease. Bingo...no more squeak. To lubricate the rollers, remove the retaining clip and pull the wheel off. I put an even thin coat on the post they rest on and the inside hole of the wheel. Replace them and remember to put the retaining clip back on. Now replace the belt onto the metal pulley first, with the threaded side of the belt down towards the drive shaft, it should loop around the drive shaft and then you can pull it around the drum, slowly feedingthe drum farther and pulling the belt back along the drom. The smooth side of the belt should be on top of the drum. Now you have to reach back under the drum on the bottom right corner below the lint trap and pull the belt over the tensioner. Sounds harder than it is. Volia...that should fix it. Its been 3 days of non-stop laundry since the repair and no squeak. Next time I will purchase the replacement roller package, but this worked for now. Good luck.

This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner sprung to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

unplugged unit, opened lid, removed 2 screws & door switch from front panel, removed front panel & drum.
Removed clips & washers from rear roller shafts, removed 2 screws (each) attaching rear roller shafts to rear of unit. Replaced rear roller shafts, thrust washers, rollers & clips. Removed clip from belt tensioner idler arm, replaced idler pulley wheel & clip.
pulled tensioner toward motor side and locked in place with broomstick. Placed new belt over drum & installed drum/belt into unit, engaging rear drum lip over new rear drum support rollers. Guided belt
over motor shaft and slowly released broomstick to
tension belt. Turned drum by hand to ckeck belt tracking. Reinstalled front panel & door switch, installed 2 screws holding front panel to case. Closed lid. Plugged unit in & tested for proper operation-OK.

First I disconnected the power cord. Next the top of the dryer was easily popped upen with a screw driver by inserting it between the top panel and the front door panel. I removed the two sheet metal screws that held the door panel on the upper right and left sides. The door panel was easily lifted up and out and set it to the side (the door switch can stay connected, the wire is long enough). d I pulled the drum out from off of the rollers that hold the drum in place. No need to remove the belt, it stays in place. I reached through the drum and removed the two hex-head screws that held the roller in place ( I only replaced the left one) and added the new one. I pushed the drum back in place over the rollers (it snaps in place). I propped the drum up with a short screw driver to raise it off of the right and left drum glides (on the bottom). I replaced the felt pads and the plastic glides and set the drum back in place. I also replaced the felt ring (seal) that circles the door opening that the drum also glides on. I glued it in place in spots (with gasket glue). It folds back over itself and forms a double thick pad. You will see what I mean when you see how the old one looks. I replaced the front door panel and snapped the top panel back in place. I let the dryer set over night so the glue would set up. I turned it on the next morning and it is as quiet now as when it was new. Oh ...Jay (the husband) did the work not Jean the wife (her dryer, her credit card)

Always begin repairs by unplugging the power cord from the power outlet! First, push in the 2 taps under the dryer top to lift it up and secure it at a 90 degree angle. Remove the door light switch from the retaining clip and let it hang to the outside of the dryer. After removing the 2 scews inside the top front, remove the front dryer cover. Next, remove the screws holding the blower cover and set it aside. Using a pair of plyers, remove the hose clip from the blower axle. Use a c-clip tool to remove the c-clip and pull out the blower wheel. Use a vacuum attachment hose to remove lint and other dirt from the wheel housing and dryer. Apply a light dish soap to the motor axle and slide on the new blower wheel. Replace the blower housing cover, front dryer cover, light switch, and close the dryer top, making sure to allign the pins and holes near the lid clips that secure the dryer top. Plug in the dryer power cord and you are set to go! Retire to your favorite lounge chair, grab the remote, and tell your wife that it is OK to "test" the dryer! However, do not attempt the last step until AFTER you have cleaned up all the mess you made while making the repair!

used a flat blade screw driver to open top up(like a car hood) then removed two screws that held the front panel on. Two more screws held the lint colector part in place. The only problem that I had was that I had to use Elmers white glue to hold the gasket that ran around the lint colector in place.Just a little dab, not enough to soak it.When I took the part out there was about a volleyball's worth of lint in the fan blower. Ordered the part and 2 or three days later I had it. If I need another part I will be back...

I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (it should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.

I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.

I followed the directions from a post on parts select that somebody had previously written and my repair worked out perfectly. I removed the top / lid of the dryer by placing a flat head screwdriver underneath both top front corners which was relatively simple. I then removed the entire front door of the dryer by disconnecting the electric wires for the door which again was a very simple procedure. The tumbler was now exposed at which time I removed the belt (I took a picture of the belt setup for later reassembly) and lifted the tumbler off giving myself easy access to the rear drum rollers and front drum pads. I was able to see that the wheels were worn and definitely the cause of the squealing. I changed out the wheels with replacement wheels which was self explanatory. The front pads were in good shape but I figured that at this point it would serve me well to replace them also which I did. I then reset the new belt (another part that I opted to change while I had the opportunity) on the tumbler with the picture in hand and had no problem. This step did require two people but still not a difficult step. I then put the door and lid back together and now had myself an extremely quiet dryer and a piece of mind that new parts were installed. All in all pretty easy repair.