AWM472W Amana Washer - Instructions

Followed video on PartsSelect website, they made it real easy.

The repair was easy. It took approximately 30 minutes.

Removed front cover of machine. Removed motor/pump assembly which was held in by four (4) bolts. At the same time removed belt from transmission pulley. Removed pump assembly from motor, held in by three (3) torx fasteners. Before installing new pump installed new belt on motor assembly. While setting the motor/assembly in place threaded belt around transmission pulley. Fastened motor/pump assembly. Very easy process!

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.

Just took it apart and figured out what was leaking. Ordered a piece online through Partselect. Got the piece in 2 days and put it back together. Went real smooth, saved us from buying a new washing machine. Thanks! My husband is quit the handy man too! So I thank him too!

First, I removed the screws, then removed the pump. I, then, installed a new pump.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

I removed the front lower panel. I disconnected the springs holding the motor to the chassis. I removed the belt off the pump pulley. Pay attention to the way the belt runs from the pulley and through the pump. This will aid in placing the pump back on so the belt runs correctly. Disconnected the wires, removed the capacitor bracket so I could take the motor/pump unit out after I removed the 4 bolts holding the motor/pump unit. Removed the 3 torx screws holding the pump to the motor. Matched the new pump to the old to make sure the new one was correct.

Installed in reverse order.

Pulled the old knob off and replaced with new knob
PartSelect sent me the exact part you can't tell the difference.

Unhooked the idler pully spring, removed the 2 hoses from the pump outlets, unhooked the idler pulley srring to slaken the drive belt tension, removed 4 bolts from the motor mount to drop the motor, and slipped the drive belt off the transmission pulley.

Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.

The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!

I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.

removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse

remove front panel. unplug motor. remove 4 screws and take motor,pump,idler and belt assembly out. remove pump from bottom of motor. 3 screws held pump and drove off with hammer. replace idler and install belt before new pump. install pump. reinstall assembly. works good now.

First I unscrewed the bottom of the front panel.
Then I realized the front panel pulls off from the top.
(manuals are helpful only if read!) I took the tub hose off at the tub and used my wet vac to remove all the excess water. (no towel needed) Using the appropriate size torx head bit, an extension and a small socket wrench to undo the screws holding the pump. I had to push and pull the bottom of the tub slightly to get proper room for the small socket wrench. pull the pump down and off. take the hoses off and place them on the new pump. reverse the process. tighten the clamps and replace the front cover.