AW26L3WK Admiral Washer - Instructions

remove top and front panel to access wash drum. unhooked suspension/balance springs(6).also removed drive belt. removed half of brake bolts installed 3 1-inch bolts removed 3 remaining short bolts,then 3longer bolts to remove tension of brake spring. removed/dissassembled brake and snubber ring,then reassembled in reverse order. wish i would have replaced suspension springs at same time! ordered new springs today

tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.

Tilted machine back, put a paint can under it and did R & R with belts.

I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.

Iwill use your service again,thanks.
Loyce Floyd

I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).

I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

Removed screw, replaced hinge.

I changed the piece easily

I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.

Rolled the old one off and rolled the new one on.