ASD2522VRB00 Amana Refrigerator - Instructions

Was easy, removed several screws and a clip on the auger shaft. removed broken part and replace with new then reassembled

The only problem I had was the nut at the end turned the opposite direction. Once I realized that I took it apart in sequence and it went right back together. It helped me in that I slid all the parts off the auger shaft onto another small rod I had and then slid them right back on. Was no problem

removed three screws

The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.

I found the part I needed on this website, watched the tutorial and saw how simple it was to do myself. I ordered the part and it arrived within a few short days. It took me no more than 15 minutes to change out the part. I saved myself several hundred dollars. It is rather shocking how much the "professionals" charge considering the cost of parts, labor and nominal service fees.

what I discovered is the condenser fan is still operating but not strong another word insufficient cooling for the condenser. therefore, it's getting too hot and shutting off and stripped the circuit breaker. After installing the new condenser fan, it gets back in business. it's quite simple. Just unplug the unit off, uncover the bottom back cover and there you see compressor, condenser fan and other good stuff. there you unscrew the nut in front of the condenser fan and remove the fan, then it expose the two screws that holding the fan motor, remove these screws and take out the motor. and just install the new fan motor kit in and there you have it. plug it back to the wall and there it goes

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The black wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.

Used 1/4 inch nut driver with swivel to remove the part retaining screw. Held new part into place and installed the retaining screw. Challenge was not hitting the level and putting water on me and the floor during installation. Relatively easy installation as long as you have patients.

watched the video on your website, assembled the tools needed, then replaced the bracket. It was so easy because I would play one step in the video, do that step, then repeat for the rest of the video. Very happy with the part and speed of service with partselect.com and the video was excellent !!

The instructions on line suggested I buy a lower door closing cam and a thimble top which I did. When I went to install I noticed that the door hinge with cam was also warn down. I had to again place an order and again remove the door to install. I would suggest those having this problem that they look at the hinge with cam also before ordering.

Removed the refrigerator door (after taking everything out of the shelves). Took the old Lower Door Closing Cam off (it was totally worn down), installed the new one, rehung the door. Rehanging the door took a couple of tries to get it properly aligned. Very easy fix, We thought we had to replace the refrigerator since it is 14 years old, but this fixed the problem completely!

Watched Parts Select YouTube video for demonstration of installation. Went smoothly.

I took out three screws and unhooked the wireing harness and lifted out and put the new one in put back the three screws and it took the ice maker 24 hours before it would do any thing. it wokrs but very slow making ice.dumps one tray full every 12 hours. works very slow.

remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis