ASD2522VRB00 Amana Refrigerator - Instructions

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

Repair was just like in the video, and the trouble shooting tips on here were great. The most highly probably issue for the broken bracket was exactly what my issue was. It was fixed in no time.Thanks, Tim

Pulled out refrigertor to get access to back. lower right hand corner where water vavle located. Removed water valve cut water lines to adapt to push type fittings on new vavle and replaced vavle. Pushed water lines all the way into proper water outlet, they cannot be reversed different sizes, plugged the two electrical fittings pushed refrigertor back in place after plugging the refrigerator back in.

I watched the video and removed the tray, but there were no screws underneath it! We tried prying it off with no luck, and then I read the directions from another customer. We removed the door handle, pressed down on the dispensing unit while using a flat head screwdriver to pry off the dispenser unit at the bottom (There are two little slots where the screwdriver fits perfectly.) I was afraid of the thing cracking since it is so old, but it did fine. This was the only hard part. After this was off, the rest of the repair followed the video exactly and it was super easy and took about 5 minutes! As I was detaching the old control bracket, I saw that it was completely broken on the right side. I knew then that this was the correct fix. It was an incredible moment when we tested the dispenser for the first time and water came shooting out! Thanks for your help on this - I would have never dreamed doing a repair like this before, and now i know I can do it.

watched the video and went very well. No problems. I am sort of handy at repairs, and found this relatively easy.

Pulled the refridgerator out from the wall . Unplugged it and shut off the water supply. Removed the rear lower panel . Removed the 2 bolts holding the bracket to the frame. Took off all 3 plastic nuts and pulled the lines out. Had to drill the bracket hole to remove it from the smaller bracket. Cut off the ends of all 3 lines. Mounted the new valve to the bracket. Pushed the lines into the new valve connectors. Bolted the bracket back to the frame of the refridgerator. Turned on the water and checked for leaks. Reinstalled the back lower panel and plugged in the power. Tried the water and everything worked now.

First I watched the little video that was available when I bought the part on line. Though the job was easy, it was a VERY good idea to watch the video. Just makes you more confident to do the job well. The whole thing was done very quickly and to satisfaction

Got on your website and found our refrigs expanded layout and ordered the part. The removal and install was less than one minute Including the clean up.

I followed the video. And it was a big help

Followed the lead of david from chesterfield in prying off out cover, unplugging it and setting it aside. Unscrewed and pulled out next assemply, and taped it above work area to avoid having to unplug. The pried pulled out pin to right holding ice door hinge to remove old unit. (Notice which way the spring faces before removing!) unplugged it. Ended up taking off push-dispenser handle (one screw on right) to get easier access. Then reinserted long pin being careful to have spring with two long tongs pointing down. Then put everything back together. Use all parts!

First I watched the video on how to do it, then I tried it. First I disconnected the electrical. Then 2 screws in the front. Opened the front and disconnected the electrical wires that are all color coated. Took out unit and replaced it with new one. Put the unit back and was finished. Thanks for the help with the video.

Great! I actually replaced the Auger Drum while watching the step by step video on my PC. Do not think I could have completed this replacement so quickly without the video. I would recommend PartSelect to anyone. Thanks

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

After watching the vidio I think my wife could have done this repair. It took me about a half hour and the job was done. It cost me $20, No telling what a repair man would have charged. Thank You.

Was easy, removed several screws and a clip on the auger shaft. removed broken part and replace with new then reassembled