Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Baking Element Went
The hardest part was the two screws (they were baked on I guess). We turned off the breaker, put paper towels in the oven carefully sprayed wd40 on the screw. Waited about 5 minutes unscrewed the two screws, gently pulled out the plate. When you pull the two wires out there are two contacts. Look at the direction their on. Slide them off put in the new unit to the contacts, gently slide back in and put the two screws back. It was really that easy and I had no idea what I was doing. No need to pull oven out can all be done for the front side.
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge. Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.
Old hinge snapped a rivet. It could no longer hold the weight of the door.
I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Unplugged oven. Took screws off top backside cover. Pulled off oven knob. Pulled wies off backside of krc electric module, Making sure to remember the order of the wires. Took off four screws on the module and pulled it out. Pulled off the touch pad plastic from the old module. Put old touch pad plastic on new module. Replaced new module with the four screws. pushed wires back on. Also, replaced left side back guard end cap, by unscrewing the three screws that hold it. I then replaced top backside cover. pushed back on oven control knob. Plugged oven in and tested it. Now its as good as new.
Received part after one working day and was installed in five minutes.. Would recommend as a do it your self project with the support of PartSelect.com
I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).
* * * * I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)
Oven would not stop heating even with Bake turned off!
The lower element had burned out but in the process, it developed a short from line to neutral. Since the short was located about 3/4 of the total length from the one hot leg (L1) and the other hot leg (L2) was the relay controlled leg, there was a current path that allowed the element to heat even with L2 disconnected by the relay. Actually replacing the element was easy, just remove the back cover(s) and the element mounting screws (2) inside the oven cavity and the new unit slides into place. Reconnect the two wires to the new element and replace the back covers. Back in business and the cookies are coming out perfectly!
Top (broil) element broke in two on oven. Ordered part,it was there in three days. Quick fix, removed screw holding element to oven wall, unplugged wires, then just swaped out elements. Re-attached wires just as they were on old element and screwed back into same place and oven is working again.
A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like clockwork. I would definitely order in the future. Thank you.
Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.
I unscrewed the 3 screws that held the element in place. My husband disconnected the back wired part of element .Then he reconnected new element wires and I rescrewed 3 screws in of new element. Very simple. I just wasn't sure about the back wired part, but like I said my husband seemed to know what he was doing so I let him do that part!
Pulled stove out, unplugged it and took 4 screws out to get access to control board. Marked and removed all electrical wires and took 4 more screws out and took of oven knob.Replaced the control board and put everything back together.
