Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Small burner full hot all the time.
TURNED OFF POWER TO STOVE Removed 5 Knobs, 2 screws that held bad switch. Removed 4 screws and lifted panel up and forward to expose switches. Adjusted spring tension on knob stem to hold knob ( stem in new switch slightly smaller) removed wire from defective switch one at a time and fastened to new switch in sequence. Reassembled and turned power on. Defective switch had stuck contacts making it full hot.
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Received part after one working day and was installed in five minutes.. Would recommend as a do it your self project with the support of PartSelect.com
replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Top (broil) element broke in two on oven. Ordered part,it was there in three days. Quick fix, removed screw holding element to oven wall, unplugged wires, then just swaped out elements. Re-attached wires just as they were on old element and screwed back into same place and oven is working again.
I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).
* * * * I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)
Sparks emitted at burner connection and burner does not work.
1. Turn off circuit breaker, pull out element and remove reflector pan. 2. Unfasten terminal block mounting screw and remove terminal block from casing. 3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire. 4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions. 5. Heat shrink sleeves per instructions.
Oven would not stop heating even with Bake turned off!
The lower element had burned out but in the process, it developed a short from line to neutral. Since the short was located about 3/4 of the total length from the one hot leg (L1) and the other hot leg (L2) was the relay controlled leg, there was a current path that allowed the element to heat even with L2 disconnected by the relay. Actually replacing the element was easy, just remove the back cover(s) and the element mounting screws (2) inside the oven cavity and the new unit slides into place. Reconnect the two wires to the new element and replace the back covers. Back in business and the cookies are coming out perfectly!
I unscrewed the 3 screws that held the element in place. My husband disconnected the back wired part of element .Then he reconnected new element wires and I rescrewed 3 screws in of new element. Very simple. I just wasn't sure about the back wired part, but like I said my husband seemed to know what he was doing so I let him do that part!
Stove-top Burner intermittently shut off and on-wouldn't heat properly
removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!
Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.
Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hooks towards the front of the oven near the door and removed.
The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.
After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.
