ARR629L Amana Range - Instructions

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.

Turned power off! Removed two mounting screws, disconected two slip on wire terminals from heating element. Removed Element from oven. Took about 10 minutes.
Part came in two days. Re installed heating elemet by pushing on the two slip on wire terminals and re installing the two mountint screws. Took about 10 more minutes.
We have been retired for 17 years. Wish all my "Honeydew jobs were this easy!

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.

Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hooks towards the front of the oven near the door and removed.

The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.

After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.

Good to go now!

just plugged it in!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The repair went real easy. Turned off power, unscrewed two screws at back of oven and disconnected the two wires. Reconnected two wires to new broiler element and remounted the new one with the two screws. Turned the breaker back on and had a steak cooking in no time.

Shut off power to the oven.
Unscrewed the old broiler element, unplugged it.
plugged in new one, screwed it in.
Turned on the power. Voila!

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Indicators showed broiler should be working so basically made a guess that the element was bad and replaced it. Turned off circuit breaker and removed mounting screw and unplugged terminal ends of the element and replaced with new one. Switched circuit breaker on and turned on broiler and my repair was a success.

Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!

had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.