Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Propane dryer would not ignite
Cover of the dryer pops off and hinges back. Use a flat screw driver to pop the clips on the front sides. Two phillips head screws hold the front panel on. Remove them then lift the panel off the clips at the bottom. Two phillips head hold the Ignition Coil bracket in place. Take note of the direction of the cable connection, it's not marked. Dryer would ignite intermittently. Clothes were not dry after 1 hour.
dryer would dry for the first 5 min them make noise with no heat.
my experience was just like the other responses. top comes off, 2 screws and the front comes off and the screws to the solenoids come off. Replaced the solenoids and put everything back together.
i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done
Dryer made a loud squeaking noise was ready to get a new one
I first diagnosed the problem using a Google search. Amazing how many hits I got and after reading a few was pretty certain what the cause was and what parts I probably needed to make the repair. Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive. Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes. So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it. I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around. Kevin
I followed the instructions on previous posts. The only problem I had was trying to remount the drum to the bearing unit which sits in the back of the driver. I just couldn't get the three holes lined up for the screws until I finally laid the dryer on its back, and then presto! - it went together in seconds.
This project probably took me longer than most people because I'm always looking things over and a little cautious in my work. I never realized how simple a dryer system is until I had dismantled this one. I spent $38 to fix my dryer rather than buy a new one. $10 of that was for the belt which I changed only because I was in there. Parts from partselect.com arrived 48 hours after ordering, and I used their basic shipping.
The drum belt was making a squealing noise, and it looked frayed.
After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect PS this dryer is 23 years old.
My dad and I followed the video instructions and it was easy! No more ear piercing noise! I did find that once we took the front of the dryer off there was a lot of lint! Never thought to clean the front of the dryer out! The video was a great way to see exactly what you needed to do, just follow what they say and you will have no problems!
Tip: After pre-taping the threads on the ball shaft, use painter’s tape to hold it in place while you attach the screws. Do the same with the bearing retainer. Don’t use tape that will leave a residue when you remove it or your clothes will smell like adhesive. Tip for stacker dryer: There is no need to remove the wires connected to the front panel. Swing the panel around to the side. Put a small bungee cord through the door opening and attach it firmly to the top of the dryer. Make sure the cord carries all the weight and that there is no strain on the wires.
My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).
Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.
