AFI2538AEB Amana Refrigerator - Instructions

The nipple on the "pantry end cap - left side" that acted as part of the hinge for the meat drawer cover broke off. After receiving the replacement pantry end cap, I removed the meat drawer, removed the 2 vegetable bins, removed the glass shelf above the meat drawer, removed the screws holding the old pantry end cap, and pulled the old cap out. Then I put the new cap in place, screwed it in, and replaced everything else. The most surprising part of all of this is that I ordered my part on 4/22 and received and installed it on 4/25; 3 days! Thank you partselect for your fast response.

Found glass here and ordered. Had it 2 days later and set new glass in and back in business.

The rail & the drawers need to be aligned with each other & then push the rail into the little hole in the back wall of the frig while sliding the drawers in at the same time. I think I put too much fruit & vegs in the drawers which makes them heavy & the little tab which is there to support the drawers has broken off twice. This is the 2nd time I have ordered this rail. It would be helpful if the rail had a vertical supporting post towards the front. I like to have a lot of produce on hand all the time

Removed Left side support with broken pin (3 small hex head bolts). Replaced with new support with pin in place. Note behind: I broke the pin trying to replace the cover. Now I know to flex back the side to the cover, and not flex the pin which broke. This cost me 25 bucks and one hour, saving me from a probable $300 dollar charge. THANKS, PARTS SELECT!!!!!

1. Unplugged refrigerator

2. Removed rear silver stainless steel panel on the right rear side of the refrigerator (if you are standing in front of the unit) using a small socket set. The panel is vertically located in center at the rear of the refrigerator.

4. Removed plastic cover over the HV controller board.

5. Unplugged 4 molex connectors attached to the board and carefully pushed on the plastic release locks that hold the board in place as not to break them and removed the HV controller board.

6. Inerted the new HV controller board and plugged in the molex connectors. All molex connectors are of unique size and will only attach to the HV controller board in one location.

7. Replaced plastic cover over HV controller board and attached stainless steel panel with a small socket set.

8. Plugged in the refrigerator.

9. Identified programming code inside the refrigerator.

10. Followed included instructions to enter program code to activate refrigerator front panel.

The annoying cover to the deli drawer broke off again. This is my second time purchasing this part from this website (left side and now, right side). Both purchases were very easy. Replacing the left side is easier because there isn't a temperature adjuster to remove and reinstall. I found this website very easy to find my parts both times, and I installed the right side (the latest fix) in less than 15 mintues while taking care of two kids. Many women do repairs around the house and are successful! :)

Super easy. 1) Remove beer from the bottom the glass shelf. 2) Remove the glass shelf. 3) Remove the broken Center Rail. 4) Replace the Center Rail. 4) Clean and replace the glass shelf then the beer (keep one bottle for consumption). ** NOTE: PartSelect was very simple to navigate and identify the correct part needed. Shipped/Received in a couple of days. The part was correct. Couldn't have been easier.

The repair is staightforward. Simply remove the deli drawer (up and out), the glass lid, and the vegatable drawers above it (easier access- they just slide out). Using a 1/4 socket I removed the 3 screws holding the end cap in place. You then disconnect the 2-3 places where the end cap connects to the humidity adjustment (front and rear). When the end cap is out you have to remove the drawer slide as and humidity adjustment slide as it isn't included in the replacement part- just 3 more screws- same size). Attach the drawer slide to the new end cap and do everything in reverse to replace it. Took all of 20 minutes including cleaning/drying the drawers etc while I had them out. Easy project.

Replaced the water filter with the bypass plug. The water in western NC is perfect out of the faucet.

Followed your internet instructions. Saved $1200!!

we only had mm sockets so had to go to the hardware store when we found they would not fit. We needed and american socket i/2 way between #6mm and #/7mm which turned out to be a 1/4 inch socket

I took all the food out and the shelves above the area. The end cap was a piece of cake to remove, only two screws to take out, and installing the new ones was very easy.The reason it took so much time is because I thoroughly cleaned the fridge at the same time.

Removed items from frifge, took out the lower drawer, removed side plate with broken part by nutdrive, replaced it, and put everything back - about 15 minutes. Easy.

Logged in to internet, for whatever reason I selected your site. Good choice! Entered the model number and selected the symtems identical to my refrig. Ordered the recommended parts, (Relay and Start Capacitor), to solve the problem. Reviewed the remove and install video. Received parts as promised by del date. Installed parts under 15 minutes, Frig kicked in and frig has been working beautiful. Avoided all those added expenses of; home service check, amount of days in- shop repair, plus parts and overhead charges. Will recommend site to my friends.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.