ADB1400PYW2 Dishwasher - Instructions

Replaced the lower rack. The replacement part had the wheels attached. No assembly required.

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

turn off power---open door--remove 12 screws holding front door panel on--remove door panel--tape upper protection cover in place--remove 2 wire plug to dispenser-- remove 6 screws holding dispenser--remove dispenser--re assemble in reverse directions above

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.

Followed the instruction that you provided with the part and har no problem. Took about 45 minutes

I replaced the old one with a new 75.00 part with no problem. However, when I looked at the old part I saw that the problem was simply the spring that opens the door was sprung. It just needed to be adjusted. That took a little more time to fix than the replacement job but had I known this before, I could have saved myself some cash. BTW that spring is attached to the hinge on the door. IMHO it needs to be a little beefier so as not to fail.

Disconnected the power. Removed the dishwasher mount screws from under the counter. Slid the Dishwasher out. Removed the two wires. Loosened and removed the two heater support nuts. Removed the heater element from inside the dishwasher. Placed the new heater element inside. Tightened the nuts. Attached the wires. Pushed the dishwasher back in place. Replaced the under-counter support screws. Reset the diagnostics message on the dishwasher front panel (This may not be necessary for some) - (Press HI TEMP > AIR DRY > HI TEMP > AIR DRY). All works great. Thank you PartSelect.com for fast shipping and great pricing.

Pulled the dishwasher out, removed 2 wires and 2 plastic nuts, removed old heating element, installed new heating element, applied nuts, connected 2 wires pushed the dishwasher back in, drank beer (Per instructions on email - really liked).

As directed online

Took out old dishwasher rack and replaced with new.

Removed unit from counter. Replaced element.

I remodeled my kitchen with new cabinets. In order to better utilize cabinet space, I located the dishwasher away from the sink, which means that I had to have a longer drain hose. The store I purchased the dishwasher from didn't have a longer hose, so I went online and found it on this website. Thanks for the quick shipment. I ordered it using standard delivery and received it in less than three days. I have book marked this website for future use.

Empty dishwasher remove bottom basket. Disconnect electricity then turn off water. Remove top screws from counter. Slide unit out and gently tip forward. Remove the two wires from connectors on element. Unscrew plastic nuts from element save if reusable. Gently tilt unit back to normal position. Remove old element and install new one and attach to stainless spacers to hold element in place. Tip unit forward. Reinstall plastic nuts. Plug wires back into new element connectors. Tilt back into normal position. Turn water back on check for any leaks and repair if necessary. Turn electricity back on and then slide unit back into original position and replace under counter screws. Test out by running quick cycle wash. It should function normally. During drying cycle open door to be sure it is hot inside. If hot then it is repaired. Let it finish cycle and replace basket. Do not touch hot element as it will burn you.

After finding out how to replace it (on YouTube)the repair went smoother than anticipated. the difficulty was disconnecting/connecting the electrical(BX to electric hook-up to dishwasher) due to the proximity of where it was located(~1" from the floor). Other than that, the unit now works as good as the 1st day when it was bought(~6yrs ago)

Using a Torx screwdriver, I removed the fasteners holding the control panel/latch section of the door on the dishwasher. I tested the high limit thermostat with a multimeter. Just two terminals, one being power in, the other power out. The part had what I have heard call a "high resistance open". In other words, the power was not getting from "A" to "B". Power in - not out. After cutting power to the unit, I removed the part (just pull it out of the retaining clip and pull the terminals from the part). After receiving the part...by the way, really fast delivery...I reconnected the part (it doesn't matter which wire goes where), pushed the part back into the retaining clip, replaced and fastened the control panel, then restored power to the unit. Runs like new.