ABL1927FES12 Amana Refrigerator - Instructions

Took off the shelf abovethe rail and slid into the receiver in back and front. BTW, cant say enough good about the customer service received from Part Select! They were awesome!

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Remove plastic vent cover. Just snaps out. Take out two screws that hold damper cover on. Unclip and unplug damper assembly. Snap in new assembly and plug in. Replace covers. I was pretty sure this would fix my problem after observing the damper for several days. It would stay open and when I moved it by hand it would open a little more and then close. Easy fix!

This probably occurred due to overloading of the drawer, or trying to close an overstuffed drawer that put vertical torque on the front screw as the drawer was pushed shut by a 10 yr old boy!------------------------------------------(I hate it when these forms won't let you start a new line!) Ordered the part, it came in 3 days later, took longer to unload food from shelf above than to install slide. Used a hand clamp and a second small Phillips bit to align second hole while I installed screw in first hole. Then put in the second screw. total install time (not including washing all shelves since we had one out anyway... thanks honey!) less than 2 minutes.

Removed the two drawers and shelve. Inserted the new crisper rail. Replaced the two drawers and put the shelve back in. Took maybe 10 minutes. Did not need any tools.

I removed the glass on top of the Crisper and replaced the Rail and then replaced the glass. Done

first unplug unit, remove clear light cover it snaps out. there are 2 slots on either side of the light housing stick the screw driver in the slot and push the tab and pull down this will unlatch the control board housing, remove the board socket plugs, and the board from the frame, on the new board you will have to snap the PC board at the pre indented line. replace in reverse and follow instruction to program the code.

Refrigerator was not cold.

I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.

First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.

Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).

Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.

Once the board is re-installed and lock into position reverse the process and install the control panel back into position.

Next is the programing of the board. Follow the directions that come with the control board and you will be back in business

This task took about 15 minutes to remove & replace and to program.

I was so happy to find that i could order the part online and not have to call a repairman and pay for a service call. The prat shipped in one day! It was very easy to install. Only tip i will give is, make sure you put it in the right direction. If placed in wrong the drawers won't open.

Removed and replaced part...

After unplugging the refrigerator, I removed the lower rear access panel that exposed the condenser and the overload/relay start capacitor with 1/4" nut driver (6 total). Next, I unplugged the wire harness and spring loaded keeper with needle nose pliers. Then I pulled the overload/relay start capacitor out of the 3 pronged male receptor located on the side of the condenser and plugged in the new one. Replaced the keeper, plugged the harness back in, and replaced the panel. Very easy fix.

Found instructions on You Tube how to replace Jazz P/C Board Replaced board and manually defrosted evaporator coil.Everything seems to be working fine

Went very well. I replaced the ice maker itself cause of the high failure rate but that did not fix it. Measured voltage across water solenoid and it was around 1 volt. Measured the voltage at the water solenoid for ice and it was 20 volts. This was measured when it was plugged in. So I replaced the valve took 15-20 minutes including moving the fridge out. Started making ice 8 minutes later.

Pull the refrigerator forward take off the back panel and replace valve seem valve leaking