A900 - Instructions

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.

removed front panel (2 screws at base)

Raised lid panel (2 Screws under panel)

Removed old hose and water injector (2 clamps)

Installed new hose and injector and resecured panels

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

Since my missus keeps her appliances like new, it behoves us to buy something of good quality when new. We did that. Now, after almost 20 years, the washer complained it needed new belts, which I complied. Tilted it up against the wall after pulling power cord. Removed both belts and replaced. Adjusted pump belt by loosening pump and then retightening. This is easy to get to by removing front (removing 2 philips screws). Piece of cake.

Followed the first guys directions.
remove front
lift top
remove agitator
remove locking nut clockwise
remove inner tub
remove Mounting S loosen set screw and clockwise also
clean well
replace boot as shown in tip in sheet
push boot on completely

Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble.
This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)

First time I had a problem with it. Sometimes just look for the simple things !

Part select refunded me for my part that I ordered very fast.

Great Company to deal with!

Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

Removed 2 Philip screws from bottom front panel. The belts came as a set, so pay attention to the belt sizes when replacing them. Have had the new belts installed now for a week or longer with no issues. Looks like a good fix.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.

Based on info from website, sounded like it was the Belt Kit that needed replacing. While waiting for the Belt Kit, decided to take the Agitator out to have a "look-see". OMG! There was liquid fabric softener gunk so thick in, around, underneath the agitator that the unit could not get traction. The burning smell was the gunk getting hot as the agitator tried to work. After a thorough cleaning of the agitator and anything relating to it's ability to agitate, my Maytag is performing like it was brand new! I'm keeping the Belt Kit, because my washer is older and I've heard from friends and family that have purchased the new water restricted units, absolutely hate them; like the "low flow" toilets, instead of flushing once, you now have to flush 5 times. They are washing more smaller loads and double rinsing each load to get their clothes clean and free of residue. I'm a 69 year old woman who finds your website and your marvelous contributors an absolute Blessing!