A31713XATL Admiral Range - Instructions

I first matched the symptom (very long preheat time/gas odor) with the most likely problem (faulty oven gas igniter). I then wrote the model # and Googled gas oven repair and got to your website. I then located the faulty part within about 5 clicks and proceeded to order the exact part within another 5 or so clicks. I received my order from PartSelest in 2 days and had the oven working with the new igniter in about 10 minutes....Then it dawned on me---"Hey, I should be a Maytag Repair Man."
Thanks for the prompt delivery and the correct installation instructions. I will absolutely use your service again. (Not too soon, I hope !)

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

I thought that the initial problem based on the users manual may had been the thermostat.
Removal of the old unit and installation of the new one was quite simple.
The only time lag was cleaning some of the surrounding areas of the oven as worked progressed.
As it turned out though, the problem wasn't the thermostat, but rather the igniter.
But, that was a fairly easy job as well!

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

I didn't. Don't know how to get to light bulb to change it for this specific model

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks

Took the old levelling leg out and screw the new one in.

I removed all the screws that would turn with the screw driver, and the two that were near the ignitor that were much harder for to me loosen with the pliers. I then took the back off and unplugged the old ignitor and plugged in the new one. Put everything back together, and wala!, I had a working oven again. Thank you very much Part select. My husband was very proud of me, for accomplishing it on my own, He is an over the road truck driver, and I would of had to wait until he came home on the 24th of December.

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

clock is in top of double oven. Dis-assembly and access to the clock was a puzzle. Four screws in the top of the oven were the solution. The clock panel then folded out and access to three plug-ins and four screws allowed access to the clock. remounted the clock with four screws and replaced plugs. (watch carefully order of wiring) Re-power on the oven and set clock. NOTE: Cover said Magic Chef but Label said MayTag