9114538810 Kenmore Range - Instructions

At first I tried to remove the element from the top of the oven. I took out the screws with a nut-driver (1/4"). Them I tried to pull the element out slowly so I could unplug it from the power wires. One of the wires pulled off bfore I could get it out. I then pulled the range out from the wall and removed the back from it. THEN I noticed that if you pull the stove away from the wall first and take off the back the wires are right there and easy to take on and off. Then replace the the back panel, plug in the stove and test the element. It will give off a slight odor as the manufacturing coating is burned off.

just plugged in the two prings into burner into outlet. Very simple and quick.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Pulled out the burner. Just pulled and out it came. Looked you up online. Crawled around on the floor trying to find the model number. (This was the hardest part of the whole process.) Ordered the part; it came the very next day despite the fact that I didn't order special shipping. Unpacked the part, plugged it in. And it worked!!!!

FABULOUS service. Thank you so much.

Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.

Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.

Quite simple, just plug-in the new one

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!

The repair went ok. I did have to take the back off the stove in order to get to the wire connectors. Needed an extra person to move the stove out of it's location. Just had to be careful.

I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.