7MMPD6845TM0 Washer - Instructions

Removed the agitator and the broken directional cogs. Ordered the new ones; recieved them within a couple of days. Replaced the cogs; in no time the washer was working like new.

First off, the replacement lid switch worked and repaired the washer. However, the replacement procedure was very difficult. I attempted to follow the directions off of the website, and then a video from YouTube. I was intstructed to remove two screws from the back of the control panel which in turn would flip up so I could get to the old lid switch and replace it. However, there were no screws on the back side of the control panel so I removed the back panel of the washer to get to the lid switch. That was a very time consuming and laborious procedure and because the back panel was installed under the molding of the control panel I had to bend the heck out of the back panel to remove it. The good news is that the replacement of the lid switch corrected the problem. The bad news was that it was the wrong procedure on getting to the part that needed replacement. I wish that I could have found the proper procedure form my particular model.

I followed the video clip that showed how to make the repair that was attached to the email sent from Patrselect notifying me that my part had been shipped. The video clip was excellent and no other instructions needed. Thanks

Removed center top cap/sofetner dispenser. Removed center shaft bolt. Pulled off the top agitator section from bottom portion. Inside the upper agitator is the inner housing for the cogs, pushed right out. Remove cog retainer plastic ring. Careful, the cogs freely fall out and it a little tricky when reassembling. Reassemble every (cogs go in only one way), place the upper agitator back down and over lower portion in machine. Now Put the bolt back in place. Here's the tricky part. You will need a magnetic tip driver or socket to hold the bolt until you have it started because it sits in recessed "well" area. I used a dab of regular Elmer's glue from bolt head to socket. Worked like a charm. Be careful not to over tighten bolt. Remember, upper agitator should free spin one direction and "catch" in the apposing direction.

Almost identical to the instruction video that was sent. Very straight forward. I did not take apart the washer to identify the problem. I was short on time so I took a chance and ordered the highest probability cause of the symptoms indicated by your website. It was dead on; the problem is fixed. Parts were received ahead of schedule. Excellent all around.

After researching possible failure modes and reviewing a video for teardown/access from the control panel and access top down I noticed a lot of 'break dust' on top of the transmission. Shorting out the lid switch and putting my little finger on the drum, it would not spin but the clutch was spinning fine. I ordered a new clutch... Interesting thing when I was taking the clutch out... the gear it was attached to slid right off! After figuring out it was too big to go 'back' into the transmission and reviewing the parts explosion diagram... it BELONGED INSIDE THE TRANSMISSION! So I took the transmission cover off, poured out out the black-ish oil with metal filings in it, put the gear inside, filled it back up with 10W30, put the lid on, added the new clutch while it was apart and finished reassembly. Wow! It spins much better than when it was new. I guess never assume what can happen on an assembly line. Thanks for the great site.

took motor of 2 screws instaled motor coupling

It was really easy, just follow the video. The washer machine sounds like new now.

Trying to pull of the agitator top section with much difficulty it finally snaped and all the agitator pieces went flying. After watching installation videos I replaced the old worn out parts with new parts (cam kit) etc. and put the agiator back together and installed it with little difficulty. A few minutes later I was doing laundry and the agitator cleaned my cloths better than it had before I replaced the parts. Everything works great and I am very happy with my experience with Partselection.

After alot of helpful advise from you guys I replaced coupling water pump clutch, and the problem was still their. Then I tested motor capacitor and it appears dead. So I should receive new one tomorrow and hopefully success! I turned machine over and oil leak..so that's where the string with hose and air needle come in handy to put 90weight oil in through breather hole in gear case.

The easiest repait I ever made, the instruction were great.