7MGHW9400PW2 Whirlpool Washer - Instructions

Removed the old screws with a phillips screwdriver, screwed the new part on. 1 minute tops!

First I removed the screws and removed the broken pieces. I then attached the new handle with the removed screws. Easy as 1..2..3...

Removed screws, took cracked handle off, put new handle on, and replaced screws. So simple.

So easy - i just replaced the door handle with screw driver

Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.

Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.

The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.

Once the hose was out I found some bra under wires which is what probably punctured the hose.

Removed the front filter and found a bunch of nails.

Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Removed bellow clamp (used screwdriver to pry clamp open). Removed Bellow to Outer Tub Clamp with socket set. Removed Bellow. I had purchased new clamps as I didn't know condition of the old clamps. The Bellow to Outer Tub Clamp was in good condition, appeared to have an anodized finish - was not corroded and the tightening screw pointed forward where as the new clamp appeared to be galvanized and the tightening screw paralled the clamp. I assumed the new orientation of the tightening screw was to make it easier to tighten with a screwdriver, but space is limited and I had good success removing the old clamp with a socket set so I elected to reuse the old clamp. Plus, I liked the finish of the old clamp better - it had zero corrosion on it after several years, almost a decade, of use.
Reinstalling the bellow was the hardest part of the repair - it is just tedious and patience is required - I took a couple of breaks seating the Bellow to the outer tub. There was a tab on the Bellow which went to the top to insure the Bellow was properly aligned. After I seated the bead of the Bellow all the way around, I slipped the Bellow to Outer Tub Clamp over the Bellow and tightened it down - continually checking the seating of the Bellow. I then put the Bellow over the water inlet tube and seated the outer portion of the Bellow. I needed additional hands to help hold the outer clamp in place - my wife helped - and I used pliers and plastic pry wedges from a tire patch repair kit to pull it open and slip it over the Bellow - I didn't want to use screwdrives as I was afraid I would damage the Bellow.

Ran diagnostics for this model (you can look for its service manual on the web which details how to do this). The diagnostics said the cold water inlet valve or the flow-meter were broken. To pin the issue down to one component, I switched the cold/hot water control cables going into the inlet valve assembly and switched the cold/hot water hoses. Ran diagnostics again and the cold water and flow meter passed but got a failure on the hot water inlet valve. This pointed to a bad cold-water inlet valve. I ordered a replacement at PartsSelect. Installation took less than ten minutes. Machine runs like a dream. Before all this I called a service center, and without even looking at the machine, they quoted no less than $300. But with a little reading and some sleuth work, I ended up paying only $70 for the part + S/H.

Like most folks, my daughter has tossed the shipping bolts after her puechase, I moved her the first time w/o any thought to it but commercial movers won't do that, they will chg. you to have it done and it's not cheap, akin to an appliance repair. This kit contains all four bolts/spacers, (2) upper and (2) lower. Hard to tell from the decription but a sweet gal on the help desk assured me of it. Got it fast and got them installed in minutes, easy to do and wrote a big note on the back of the washer to save them!! No idea why your owners book says "do not reuse".

1st I removed the front retaining ring. You do need to get down near the ground to see the retaining ring. I used two pairs of needle nosed pliers to pull the ring apart (which has a spring in the middle) and then removed the ring.

Then I pushed the bellows into the washing machine drum, pulled the water inlet valve from the bellows, and used a short flat blade screwdriver to remove the retaining band (upper right of the bellows) After doing this it was a simple matter to remove the whole unit.

I did find it was easier to remove the washing machine door.

The installation was a simple matter of reversing the above. I had no problems with this repair. I would STRONGLY suggest, unless you are one of those gifted 3 handed people, getting an assistant to push the outer retaining ring into place as you separate the spring.

Simple, easy repair.

Had to take the entire front of the washer off to replace the door latch.

We had to bread the hinge that had rusted out. That was the worst part. Putting the new hinge was no big deal. The time factor was also great. I called on Monday and had the part by Thursay. With a family of 6 a washer is a huge necessity.

I found a you tube video with step by step instructions. Very easy to follow. Repair would have been quicker had my kids not been at home. I had to have my boyfriend help me put on the outer bellow spring clamp, as I was not strong enough. Washer works great.

Remove the lower front cover there are three small torx type screw. The pump is the very first thing you see. Have a wet and dry Vac available you will need it. The drain pump and the drain lines contain a lot of water. Unscrew the big white drain plug at the pump and clean up the water, remove the front small mounting screw and disconnect the two hoses in the back of the pump with pliers and follow the pre-printed steps in reverse. If your machine is more than six years old you will have to use a utility knife and remove a piece of plastic on the electrical connector that is from the washer wiring, if you force the connection on it will brake, look at the connection and the plug and attempt to plug it in before you install the pump. It is easy just be-aware of the connector.

Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.