7KCCC150T1 KitchenAid Trash Compactor - Instructions

I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new

Move the unit out of the cabinet, and take off the top cover.The two drive screws are easy to see. unscrew the two screws of one of the power nut covers and remove that cover. With pliers, unscrew the plastic power nut from that screw. Screw on the replacement power nut with the help of pliers and some heavy grease. install the bearing cap. Use the same procedure for replacing the plastic power nut on the other screw. To make sure the piston is level, place the cover on the power screw but do not attach it. Measure from the end of the screw to the top of the cover of the first screw, then adjust the second power nut up or down so the two power screw nut covers are the same distance down from the top of the it's power screw Lift up the piton assembly to close the gap, if any (I used a short piece of rope) , and install the screws on the second power bearing cap. After installation. recheck the distance from the top of the power screws to the power bearing caps is close to the same distance so the piston will be level.. This same procedure could be followed for other brands. Power of the appliance and verify functionality, if OK replace the top cover and push unit back into the cabinet..

Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.

Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.

The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less than 30 minutes including cleanup.The wife happy,that all that matters.
Jack

As per directions

Replace front legs. Very easy fix.

I pulled the unit out and tipped it over . I pulled the pan off the bottom then i could put a box end wrench on the screw that was jamed then tuned the screw to loosen the door . i then removed the plastic bag that was wrapped around the screw and put the new nut on and all fixed

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Only needed a flat blade screwdriver and a socket set to remove the top and the "cages" that held the power nuts. Failed to properly restrain the ram but didn't effect the repair. Installed the new power nuts outside of the unit then placed the ram assembly on the worm screws and all was well. Applied grease to the worm screws after assembly.

layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake

With nothing in the KitchenAid Instructions nor anything on the internet… I had to go it alone.
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.

I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.

I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!

I just used the accompanying screw to attach the buttons to the 4 holes in the drawer. Simple stuff.

I do think I read that the Jenn-Air bags used to come with precut holes, and the bag wold slide over the buttons, holding it in place. I jus get the bag lined up and pulled over the drawer, and cut the holes myself. It works perfectly.