666 - Instructions

I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.

1. Turned off power to trouble shoot the counter top range elements. 2. Raised the counter top up to work on it and slid two evenly placed wooden slats under the bottom of the housfor stability so it would not fall backdown into the counter top cut-out. 3. With a 1/4" nut driver removed the 10 hex-head screw that were holding the black glass top in place, pulled off the 4 . Control knobs and carefully removed the glass cover and carefully seet it aside in a safe place. 5. A visual inspection of the non working element showed that it had a burn out spot causing it not to heat. 6. Got the model number of the appliance and checked the internet for parts suppliers, chose parts elect because they had the part in stock and could overnight it for reinstallation the next day, part did arrive the next morning. A visual inspection show that it was the correct part and it would be a like for like swap out. 7. Prior to replacing the element check to see that the electrical power was still off at the circuit breaker, made a quick sketch of the wiring and identified the wires so that they would be reterminated at the same points. 8. Using the needle nose pliers pulled off the 4 stake on terminations. 9. Lifted out the 6" from the body of the unit , removed the 4 phillips screws holding parts what were to be transfered onto the new element. 10. Transfered parts onto the new element, reinstalled the element into the body of the unit, reinstalled the 4-stake-on wires to there appropriate terminals and verified with previous wiring sketch. 11. Reinstalled the glass top, 10 screw holding it in place and the 4-control knobs. 12 . Turned main power to the unit back on and turned on the replaced element, it work correctly, also checked the other 3 elements to make sure that they were working correctly. 13. When the unit had cooled, removed the wooden slats and lowered the counter top back into its cut-out making sure not to damage the glasstop. Job complete.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

My husband pulled out the dishwasher and removed the faulty part and installed the new one. We found info on the parts source website to assist us. Dishwasher works great!!! Someone from the company we purchased it from had replaced it several years ago, and the seal at the bottom had leaked and the motor had siezed because of the water. We also discoved that the water line was severly kinked in 2 places, so we installed a flexable hose. Now my dishwasher is quiet, fills much faster and all this for a fraction of the price of a new appliance. Would recommend this website.

The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I had to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.

Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

First I removed the screws holding the outside door panel to the inside door panel. Next (at this was the tricky part) was separating the panels. In our model of dishwasher, there is a layer of Styrofoam between the two panel to reduce noise. Unfortunately the Styrofoam is glued to both panels. Separating it without damage was not possible. So it was done with brute force and the Styrofoam broke in several places.

Replacing the dispenser involved removing six screws, disconnecting the wires and popping the dispenser out. The new one went in easily although there seemed to be a correct amount of tightening to do. It was tricky to get the cover back on because the Styrofoam pieces had to go back together like a puzzle.

Once reassembled, I ran the machine and it leaked at the dispenser. So the cover came back off. This time I played with the adjustment of the dispenser, testing it with the outside cover off, to insure that I had a tight, non-leaking seal. Once done, I put the cover back on and we are back in business.

The new dispensers do not have connections for the "Add Rinse Aid" light. They use a visual indicator on the dispenser itself. I simply taped the wire for the indicator light up and left it inside the door.

One last note, on our unit, the outside door panel is two pieces. I needed only to removed the lower portion for this repair. Unfortunately, I removed both and in the process broke the small plastic end on the door latch requiring me to purchase a new one. Bummer. That was a 10 minute repair though.

I removed the dishwasher from under the cabinet. This is what took the most time. Before removing the dishwasher from under the cabinet I disconnected the drain cable to remove all the water from unit. After removing the dishwasher I tipped the unit on its left side. The motor/pump assembly is held in with one screw. After removing this screw the pump/motor assembly comes out with a 1/8 turn counter clock wise. The replacement pump/motor assembly was put back in in reverse order. After the pump/motor assembly was replaced I replaced the door balance cable kit on the right side of the unit. Next I tipped the unit on to its right side and replace the left balance cable kit. After this all that was left was to return the unit back under the cabinet and hook up the water supply line, the drain line, and the power.

I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.